What have you done to your square lately??

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

carfanatic63

carfanatic63

Full Access Member
Joined
Nov 24, 2014
Posts
56
Reaction score
146
Location
Houston
First Name
Austin
Truck Year
1976
Truck Model
C15 SWB
Engine Size
454
Normmus said:
Recently found a new windshield on the local fb marketplace. Installed it today with a new gasket.
You must be registered for see images attach
Click to expand...
A new windshield always looks so good.

Finding on marketplace is a crazy find. Congrats!
 
ChuckN

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
1,299
Reaction score
3,935
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
Got ‘er back together tonight with the mixture of umbrella seals and positive locks on the valve guides. Let’s give ‘er a couple hundred miles and see what the fresh spark plugs look like. Re-lashed the valves while I was at it.
You must be registered for see images attach

You must be registered for see images attach
 
WFarm

WFarm

Full Access Member
Joined
Jan 11, 2023
Posts
324
Reaction score
2,033
Location
Central Virginia
First Name
Paul
Truck Year
1975
Truck Model
K5 Blazer
Engine Size
454
Installing a Cold Case radiator with twin 14” fans in the Blazer. Did the same upgrade on my 57 Chevy with a 383 Stroker years back and it worked wonderfully. One day I was out cruising in the 57 and got stuck in a traffic backup due to an accident. It was upper 90s but engine temps never climbed above about 200 f.

Not complete yet as you can see. Ordered a power distribution block and some other wiring goodies to make a good reliable installation. But so far everything is coming together and it’s great therapy at the end of the day as we deal with the loss of our mom.

You must be registered for see images attach
 
ChuckN

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
1,299
Reaction score
3,935
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
WFarm said:
Installing a Cold Case radiator with twin 14” fans in the Blazer. Did the same upgrade on my 57 Chevy with a 383 Stroker years back and it worked wonderfully. One day I was out cruising in the 57 and got stuck in a traffic backup due to an accident. It was upper 90s but engine temps never climbed above about 200 f.

Not complete yet as you can see. Ordered a power distribution block and some other wiring goodies to make a good reliable installation. But so far everything is coming together and it’s great therapy at the end of the day as we deal with the loss of our mom.

You must be registered for see images attach
Click to expand...
Sorry for your loss- that’s never easy.
 
fofiddyfo

fofiddyfo

Supporting Member
Supporting Member
Joined
Mar 3, 2024
Posts
92
Reaction score
245
Location
wisco
First Name
Chris
Truck Year
1987
Truck Model
R3500
Engine Size
454
She hasn’t ran in 5 years before tonight, boys and girls!!

Finally finished the install of the new fuel tanks and sending units today. Put the filler/vent necks on, and bought and installed a new battery since the old one was kaput, and wouldn’t take a charge.

She popped right off, and the ole fo-fiddy-fo big block was purring like a big ole kitten!

Hopefully tomorrow I’ll get the time to replace a couple rubber fuel lines on the right side tank, which are pretty dry rotted and leaky. Then I’d like to drive around the neighborhood and check everything out before I put the bed back on. Good times!
You must be registered for see images attach
 
Last edited:
ChuckN

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
1,299
Reaction score
3,935
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
Looks like I’m going into long hibernation mode until I can figure out what my next plan is. I happened to notice a couple rocker arm studs that had more threads showing than the others, so I took it back apart for some sampling. I picked one rocker that was appropriate with all the others, then compared the stud length with one that had more threads showing. The “appropriate “ one shows a hair less than 1 7/8 length, and the one with more threads is just over 1 7/8. At some point, there has been some migration.

It wasn’t making any noise before I did the valve seals, so it could’ve been pre-existing. I just don’t want to wait until I’m driving it and hear something start hammering. Unfortunately I hadn’t paid attention before and so I have no point of reference.

I know my dad told me years ago that he had one come out on him and he hammered it back in, never gave him any trouble. Other guys have done the roll pins, and and had screw in studs too of course.

If anyone has any thoughts I’d be keen to hear it. I think the writing is on the wall though because upon looking there’s more than one doing it.
 
bucket

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
30,424
Reaction score
28,253
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
ChuckN said:
Looks like I’m going into long hibernation mode until I can figure out what my next plan is. I happened to notice a couple rocker arm studs that had more threads showing than the others, so I took it back apart for some sampling. I picked one rocker that was appropriate with all the others, then compared the stud length with one that had more threads showing. The “appropriate “ one shows a hair less than 1 7/8 length, and the one with more threads is just over 1 7/8. At some point, there has been some migration.

It wasn’t making any noise before I did the valve seals, so it could’ve been pre-existing. I just don’t want to wait until I’m driving it and hear something start hammering. Unfortunately I hadn’t paid attention before and so I have no point of reference.

I know my dad told me years ago that he had one come out on him and he hammered it back in, never gave him any trouble. Other guys have done the roll pins, and and had screw in studs too of course.

If anyone has any thoughts I’d be keen to hear it. I think the writing is on the wall though because upon looking there’s more than one doing it.
Click to expand...

I also had one come out of place years ago, I just hammered it back in and it was fine after that. They were even heads that I had redone not long before that.
 
Ajax19

Ajax19

Full Access Member
Joined
May 11, 2022
Posts
254
Reaction score
923
Location
Socal
First Name
Ajax
Truck Year
1983
Truck Model
K3500
Engine Size
454
ChuckN said:
Looks like I’m going into long hibernation mode until I can figure out what my next plan is. I happened to notice a couple rocker arm studs that had more threads showing than the others, so I took it back apart for some sampling. I picked one rocker that was appropriate with all the others, then compared the stud length with one that had more threads showing. The “appropriate “ one shows a hair less than 1 7/8 length, and the one with more threads is just over 1 7/8. At some point, there has been some migration.

It wasn’t making any noise before I did the valve seals, so it could’ve been pre-existing. I just don’t want to wait until I’m driving it and hear something start hammering. Unfortunately I hadn’t paid attention before and so I have no point of reference.

I know my dad told me years ago that he had one come out on him and he hammered it back in, never gave him any trouble. Other guys have done the roll pins, and and had screw in studs too of course.

If anyone has any thoughts I’d be keen to hear it. I think the writing is on the wall though because upon looking there’s more than one doing it.
Click to expand...
Might not work if they are cast iron but you could take a punch and peen it if they are aluminum I'd give it a shot another option is to make some serrations on the stud so it bites
 
Ajax19

Ajax19

Full Access Member
Joined
May 11, 2022
Posts
254
Reaction score
923
Location
Socal
First Name
Ajax
Truck Year
1983
Truck Model
K3500
Engine Size
454
Ajax19 said:
Might not work if they are cast iron but you could take a punch and peen it if they are aluminum I'd give it a shot another option is to make some serrations on the stud so it bites that's just side of the road fix i can think of but then I remembered time certs drill it out and puts a oversized sleeve in there
Click to expand...
 
Ajax19

Ajax19

Full Access Member
Joined
May 11, 2022
Posts
254
Reaction score
923
Location
Socal
First Name
Ajax
Truck Year
1983
Truck Model
K3500
Engine Size
454
ChuckN said:
Looks like I’m going into long hibernation mode until I can figure out what my next plan is. I happened to notice a couple rocker arm studs that had more threads showing than the others, so I took it back apart for some sampling. I picked one rocker that was appropriate with all the others, then compared the stud length with one that had more threads showing. The “appropriate “ one shows a hair less than 1 7/8 length, and the one with more threads is just over 1 7/8. At some point, there has been some migration.

It wasn’t making any noise before I did the valve seals, so it could’ve been pre-existing. I just don’t want to wait until I’m driving it and hear something start hammering. Unfortunately I hadn’t paid attention before and so I have no point of reference.

I know my dad told me years ago that he had one come out on him and he hammered it back in, never gave him any trouble. Other guys have done the roll pins, and and had screw in studs too of course.

If anyone has any thoughts I’d be keen to hear it. I think the writing is on the wall though because upon looking there’s more than one doing it.
Click to expand...
TIME-SERT 7/16-14 SAE Thread Repair Kit https://a.co/d/32d6sQd
These will be better than new there's a guy on YT that I recommended these he used then on his turbo build with Chinese heads and they were pulling out a few studs I have used them a few times on Hondas for the timing belt tensioner that has a bold just going into the soft aluminum block these are about as good as you can get another redneck option I thought of just give her a few tacks welds heat the head with a torch and send it lol just need to use high nickel flux core
 
You must log in or register to reply here.

Similar threads

Strick
What I have done to my Square lately…
Replies
1
Views
155
Strick
Strick
S
Oops. Probably shouldn't have done that.
Replies
11
Views
2K
dsteelejr
dsteelejr
Randy and Easton
  • Sticky
Easton Is Graduating Thank You all for your help GMSB!!
2 3
Replies
31
Views
4K
Randy and Easton
Randy and Easton
D
Thank you post to y'all.
Replies
3
Views
1K
Catbox
Catbox
RanchWelder
Identifying GM Transfer Cases: Show us in pictures what you have with measurments and Adapters.
2
Replies
19
Views
5K
dragstews
dragstews

Latest posts

Forum statistics

Threads
44,102
Posts
949,398
Members
36,200
Latest member
cj7_hvn
Top