Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
legopnuematic's latest activity
legopnuematic
reacted to
Rustisbest's post
in the thread
Valve cover bolts won't stay snug.
with
Like
.
The front spreader ain't spreadin'. It's upside down
Jul 23, 2024
legopnuematic
reacted to
Ricko1966's post
in the thread
Rear End Recommendation for 87 with an LS
with
Like
.
Are you looking for a new ready to purchase rearend? Or are you asking us if there's a junkyard pick that has better gears,a posi and is...
Jul 23, 2024
legopnuematic
reacted to
bucket's post
in the thread
Help with difficult problem!!! ‘83 K5/4” lift/NP208 mounting height with incorrect homemade spacers vs correct spacers???
with
Like
.
That is the correct crossmember for an '83. Is it possible that you have the crossmember flipped around backwards? How far off are the...
Jul 22, 2024
legopnuematic
reacted to
Johnny Atomic's post
in the thread
What have you done to your square lately??
with
Like
.
Cleaned it up, changed out a couple ground cables for some thick boys I made from welding leads, and changed out short filter and air...
Jul 22, 2024
legopnuematic
reacted to
TotalyHucked's post
in the thread
What have you done to your square lately??
with
Like
.
Drove it for the first time in like 2 weeks, to work cuz it’s been at home waiting for my Ram to sell.
Jul 22, 2024
legopnuematic
reacted to
Oldbear42's post
in the thread
Valve cover bolts won't stay snug.
with
Like
.
From a young age, I was taught to give each bolt hole a light tap with a ball-peen hammer (ball-peen held to metal and stuck with...
Jul 22, 2024
legopnuematic
reacted to
WFarm's post
in the thread
What have you done to your square lately??
with
Like
.
Continued detailing under the hood and underside, and went for a drive with the Mrs. Neighbor saw us and took a couple pics. Sold the...
Jul 22, 2024
legopnuematic
replied to the thread
New GMC Owner with shifting troubles
.
Welcome from Missouri.
Jul 22, 2024
legopnuematic
reacted to
bucket's post
in the thread
Confusing info on tightening spindle lock nuts
with
Like
.
It doesn't hurt. Either that or pour some fluid into the hub before installing the axle shaft. That way there's lube in there as soon as...
Jul 22, 2024
legopnuematic
reacted to
DoubleDingo's post
in the thread
Confusing info on tightening spindle lock nuts
with
Like
.
So, in the case of axle bearings, would you recommend dunking them in gear oil, as opposed to installing them dry? I can see grease...
Jul 22, 2024
legopnuematic
reacted to
bucket's post
in the thread
Confusing info on tightening spindle lock nuts
with
Like
.
Ok, that's was I was assuming, but wasn't sure. I wondered because in this case, packing the bearing with grease is the wrong thing to...
Jul 22, 2024
legopnuematic
reacted to
Ricko1966's post
in the thread
Valve cover bolts won't stay snug.
with
Like
.
As said by multiple people you should have spreaders,they were factory. I never had a problem with cork gaskets I glued them to to the...
Jul 22, 2024
Latest posts
OEM Breather replacement
Latest: AuroraGirl
1 minute ago
Garage
K
Vintage Air Gen V (5) or replace existing compressor, etc., for 1987 R20 Suburban?
Latest: Knuck55
2 minutes ago
Heat & AC
I finally got my hands on a squarebody!
Latest: Doppleganger
6 minutes ago
Introduction
8
83 resurrection i
Latest: 83twentyfive
10 minutes ago
Introduction
tranny mount/crossmember- urgent help needed
Latest: SquareRoot
20 minutes ago
Transmission & Transfer Case
Forum statistics
Threads
43,515
Posts
937,065
Members
35,397
Latest member
sqrbdy
Members
Top