What have you done to your square lately??

[78C10BigTen]

Well first thing this morning i got pulled over by a cop and told my window tint is way too dark. First off... no **** i knew that when i put it on and second, its been that way for 5 years im not changing it now. So he asked me if i needed a warning or if i would take it off. Being polite i told him id take it off but knowing damn well, thatll never happen!

 

[80BrownK10]

Well first thing this morning i got pulled over by a cop and told my window tint is way too dark. First off... no **** i knew that when i put it on and second, its been that way for 5 years im not changing it now. So he asked me if i needed a warning or if i would take it off. Being polite i told him id take it off but knowing damn well, thatll never happen!

How big a town do you live in?? What are the chances that dude sees you again, recognizes your truck, squares are not inconspicuous and catch everyone's eye, gets pissed and rips you a new one for not complying?

 

[82sbshortbed]

How big a town do you live in?? What are the chances that dude sees you again, recognizes your truck, squares are not inconspicuous and catch everyone's eye, gets pissed and rips you a new one for not complying?

Good point

 

[Shorty81]

How big a town do you live in?? What are the chances that dude sees you again, recognizes your truck, squares are not inconspicuous and catch everyone's eye, gets pissed and rips you a new one for not complying?

You are marked now. Better comply....

 

[80BrownK10]

Good point

If I did that around here, I might get by for awhile..only cause I don't go to the larger town that often in my square. If I did it was n the closest town to me that has cops...it might work till the next time I was in town and that guy was on shift! Haha

 

[78C10BigTen]

How big a town do you live in?? What are the chances that dude sees you again, recognizes your truck, squares are not inconspicuous and catch everyone's eye, gets pissed and rips you a new one for not complying?

Well the town i got stopped in is small and it was the chief who stopped me (my gf knows him well). Most likely i know for a fact he will see me again but im not too worried because i drive through that same spot often and its actually right at the interstate exit. But also every vehicle ive owned had the same % tint because ive always used the same one, this truck has had it on for almost 5 years now and hes the first cop to stop me about it. This is only the second stop ive had for tint, first was way back in the early 2000's when i had my s10, still the same tint. All my vehicles have always gotten 5% on them. Also if need be i can remove it in an instant on the spot, its static cling tint

 

[CoggedBelt75]

Spent 8 hours in the garage today and finally made some progress on my project.

You must be registered for see images attach

 

[CoggedBelt75]

Gots y’all a few pics from today. Finally got it in and mounted once the din cable was hooked up. Shifter mounted and wired up. Shift cable ran and hooked up. Adjustment is close enough until I can raise the rear and run thru the gears under power. Starts in gear and neutral only...check. Backup lights...check. Trans brake engages...check.

You must be registered for see images attach

For now, seat just sitting in place. Column shift handle removed.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Still have to fab a 2 foot heat shield to protect the shifter cable and fasten to exhaust with 2 muffler clamps, get a cable clamp and secure cable to tranny tail section, and screw the top lid hinge down on the console. Baby stepping it, but getting there. B-day tomorrow so not sure if anything gets done or not.

 

[nabeshin]

All my vehicles have always gotten 5% on them. Also if need be i can remove it in an instant on the spot, its static cling tint

I had no idea they had static cling tint. How does it look? I imagine static cling tint to be crummy and full of bubbles and then scrape off when the window goes down.

 

[Old77]

Gots y’all a few pics from today. Finally got it in and mounted once the din cable was hooked up. Shifter mounted and wired up. Shift cable ran and hooked up. Adjustment is close enough until I can raise the rear and run thru the gears under power. Starts in gear and neutral only...check. Backup lights...check. Trans brake engages...check.

You must be registered for see images attach

For now, seat just sitting in place. Column shift handle removed.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Still have to fab a 2 foot heat shield to protect the shifter cable and fasten to exhaust with 2 muffler clamps, get a cable clamp and secure cable to tranny tail section, and screw the top lid hinge down on the console. Baby stepping it, but getting there. B-day tomorrow so not sure if anything gets done or not.

Best update ever!!

 

[Poppy 87]

That looks great! Where did you get the seats from?

Sent from my XT1254 using Tapatalk

 

[78C10BigTen]

I had no idea they had static cling tint. How does it look? I imagine static cling tint to be crummy and full of bubbles and then scrape off when the window goes down.

If you do it right when you put it on it looks great. After awhile it goes to **** though.

 

[TravisB]

Gots y’all a few pics from today. Finally got it in and mounted once the din cable was hooked up. Shifter mounted and wired up. Shift cable ran and hooked up. Adjustment is close enough until I can raise the rear and run thru the gears under power. Starts in gear and neutral only...check. Backup lights...check. Trans brake engages...check.

You must be registered for see images attach

For now, seat just sitting in place. Column shift handle removed.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Still have to fab a 2 foot heat shield to protect the shifter cable and fasten to exhaust with 2 muffler clamps, get a cable clamp and secure cable to tranny tail section, and screw the top lid hinge down on the console. Baby stepping it, but getting there. B-day tomorrow so not sure if anything gets done or not.

You have as many levers as my old back hoe in this thing now

 

[TravisB]

I have had a peek inside the heart of mine lately.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[CoggedBelt75]

That looks great! Where did you get the seats from?

Sent from my XT1254 using Tapatalk

Thanks. They’re beige Pro-90 series 1300 seats by Scat Interprises. Ordered thru summit racing
Procar 80-1300-54L
Procar 80-1300-54R

Procar seat brackets ....
SCA-81196B
SCA-81197B