Thoughts on how to recover from a slightly cross threaded spark plug threads in head?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

beady

Full Access Member
Joined
Jul 20, 2024
Posts
73
Reaction score
25
Location
Tidewater/Northern Neck VA
First Name
Mine
Truck Year
1987
Truck Model
R20
Engine Size
454
Was installing a DUI distributor, coil, wires, and plugs. Got distributor and coil installed and old plugs out. Started installing new plugs and hit a snag.

454, #8 rearmost passenger side. Felt like it went in ok a few turns and then I started tightening with a ratchet, but it didn’t feel right so I stopped.

First thread of the new plug is a little rolled. Neither new plug nor old plug that came out will go in now past a turn or two, obviously I haven’t tried forcing it.

Pic of the new plug I tried to install attached, you can see the first thread is dicked up. There’s a little anti seize on it is why it looks odd.
You must be registered for see images attach


Thoughts/options?

Thanks
 
Last edited:

Goldie Driver

Full Access Member
Joined
Mar 19, 2018
Posts
4,036
Reaction score
6,619
Location
Houston, Texas
First Name
Britt
Truck Year
1980
Truck Model
GMC K1500 Suburban
Engine Size
350
My first thought would be a tool like this from a local parts store.

Get the thread cleaned up and rock and roll !

 

beady

Full Access Member
Joined
Jul 20, 2024
Posts
73
Reaction score
25
Location
Tidewater/Northern Neck VA
First Name
Mine
Truck Year
1987
Truck Model
R20
Engine Size
454
My first thought would be a tool like this from a local parts store.

Get the thread cleaned up and rock and roll !

Is that deep enough/has enough clearance to get a socket on that hex and fit into the opening in the head?

I thought I read ppl saying those were too large in some cases.

I did pick up a 14x1.25 tap this evening, might order a single ended thread chaser before I try the tap though.
 

Truck82

Junior Member
Joined
Nov 2, 2024
Posts
21
Reaction score
42
Location
Alderton
First Name
Christopher
Truck Year
1982
Truck Model
c20
Engine Size
350
My first thought would be a tool like this from a local parts store.

Get the thread cleaned up and rock and roll !

^^Same^^

I have also installed a TimeSert in my dads truck
 

Goldie Driver

Full Access Member
Joined
Mar 19, 2018
Posts
4,036
Reaction score
6,619
Location
Houston, Texas
First Name
Britt
Truck Year
1980
Truck Model
GMC K1500 Suburban
Engine Size
350
Is that deep enough/has enough clearance to get a socket on that hex and fit into the opening in the head?

I thought I read ppl saying those were too large in some cases.

I did pick up a 14x1.25 tap this evening, might order a single ended thread chaser before I try the tap though.

I bought something similar ( if not that one ) for Goldie but never used it. I THINK it will fit just like a plug socket but can't say for sure. Seems like it would be totally worthless if it did not.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,333
Reaction score
8,483
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Is that deep enough/has enough clearance to get a socket on that hex and fit into the opening in the head?

I thought I read ppl saying those were too large in some cases.

I did pick up a 14x1.25 tap this evening, might order a single ended thread chaser before I try the tap though.

Use a chaser. A tap is not first resort. A tap is designed to cut new threads,and it will,and not necessarily at the right angle and not necessarily at the right depth. Meaning you might run the tap mid thread through the remaining threads,which will substantially weaken the threads. Grease the chaser to collect the debris.
 
Last edited:

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
1,275
Reaction score
3,844
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
It’s just how my brain works, but my first thought was “of course it had to be #8! It just couldn’t be #1 or 2”.

But, it is what it is. Looking forward to seeing how this comes out- keep us in the loop.
 

Robert Bare

Full Access Member
Joined
Sep 13, 2020
Posts
81
Reaction score
113
Location
MT
First Name
Robert
Truck Year
1978
Truck Model
k20
Engine Size
5.7
You should be able to do it with a rethreader. However, there were made for years, rethreaders that expanded. You push them in, expand it, then back it out. You see, it starts down in the good threads and backs out, cleaning/cutting the threads. I would bet now only old time mechanics and machine shops have them.
 
  • Like
Reactions: WFO

tsgs84

Junior Member
Joined
Jun 8, 2022
Posts
26
Reaction score
19
Location
md
First Name
Timothy
Truck Year
84
Truck Model
K10
Engine Size
350
My first thought would be a tool like this from a local parts store.

Get the thread cleaned up and rock and roll !

I agree try a thread chaser not a thread tap
 

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
6,892
Reaction score
12,072
Location
Auburn, Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
All good advice here.
One additional thing I do is put the engine on exhaust stroke and put an open airline in the exhaust pipe so any trash is blown out.
That’s a good idea. I’m lazy so I’d clean it up then start the engine with an open hole and let it blow out any debris hopefully.
That said shouldn’t be much debris and small in size as it should only be cleaning up a thread r 2.
And my anecdotal evidence is tore down my old 400sb in high school to do the heads. Unleaded gas finally killed them….
When I did, 2 cyl had large scores in them one of which I’m certain was from a metal Jesus clip off the carb that went straight south one night during a parking lot repair! lol.
Both those cyl had the same compression after I had the heads rebuilt.
Wouldn’t recommend on a new high$ rebuild but wouldn’t sweat it too much on a presumably old motor.
JMO
Good luck!
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,333
Reaction score
8,483
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Grease on the chaser should collect the chips. I do start them with no plug in them though for just a second.
 

Latest posts

Forum statistics

Threads
43,984
Posts
947,113
Members
36,040
Latest member
75BEASTK20
Top