Engine Block Heater for SBC 350

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

WebMonkey

Full Access Member
Joined
Jan 3, 2020
Posts
717
Reaction score
1,539
Location
Missouri Ozarks
First Name
Chris
Truck Year
1985
Truck Model
K20
Engine Size
350
Thanks for your reply. What does the battery have to do with this? And if you think there is a different problem, is there a way I can troubleshoot? One thought I have is that previously I haven't adjusted the electric choke coil on the carb. I should probably do this as it will have a different tension on it in the winter. Otherwise, I'll look into soft plug heaters.
chemistry!
:)

battery chemical reaction slows, even stops at low temperatures.
used to have battery warming wraps to keep the battery in the sweet spot of temperature to deliver full discharge/charge.
the coolest battery, lifepo4 is very intolerant of cold temps.

parents kept spare flashlight batteries in the freezer to slow the discharge rate.

so CCA is cold cranking amps.
good battery is one that has enough CCA from the time of purchase and hasn't been damaged by being discharged below 50%.

yes, it's true, discharging a lead acid type battery below 50% shortens the battery life/performance.
trickle charger is your friend on a truck not started/run a couple times a week.

'monkey
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,446
Reaction score
8,679
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
I didn't read all 97 posts. Here's the deal and it's just simple math and physics. If you put a heater in the dip stick or stick one to the pan,at best you are going to get a few quarts of warm oil,that aren't even touching the block,heads,or intake,A light bulb heats in one specific area. A freeze plug heater heats water,a couple of gallons of it. Water around the cylinders,water in the heads,water in the heater core,water in the radiator,water in the intake manifold.The whole engine is preheated. If you heat the water, that's the most bang for the buck.
 
Last edited:

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,263
Reaction score
2,204
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
One risk with a dipstick heater (but also maybe an old wives tale) is that you have a heated electrical probe running down into the oil pan. If you have managed to flood out the engine you may also have gas that ran down into the pan and it’s floating on top of the oil. There is a small possibility of igniting the gas vapor in the oil pan - not a good result.
 

WebMonkey

Full Access Member
Joined
Jan 3, 2020
Posts
717
Reaction score
1,539
Location
Missouri Ozarks
First Name
Chris
Truck Year
1985
Truck Model
K20
Engine Size
350
How did vehicles run for 75 years when it was really cold out?
dunno!
furthest back i can remember was the 60s in nebraska and dad had an extension cord run out to the driveway in the winter.
watched him unplug that thing everytime he drove off to work.

'monkey see, 'monkey do

:)
 

legopnuematic

Licensed Junk Dealer
Supporting Member
Joined
Oct 27, 2016
Posts
2,506
Reaction score
6,481
Location
MO
First Name
Spencer
Truck Year
1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
Truck Model
Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
Engine Size
225/6, 350 c.i., 350 c.i., 5.9l Cummins
Back when 6 volt vehicles were still mainline people would install 4 cell 8 volt batteries to give them a little extra cranking power.

That was more of a “shade tree” type thing to do though.

There is the old tales of maintaining small fires under the oil pan to warm it up.
 

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,451
Reaction score
3,819
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
Before fooling around with block heaters, you need to get the choke sorted out. Zero degrees is not that cold.

As mentioned, make sure the battery and cables are in good condition. If the engine cranks slow, it’s not going to want to start.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,446
Reaction score
8,679
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Back when 6 volt vehicles were still mainline people would install 4 cell 8 volt batteries to give them a little extra cranking power.

That was more of a “shade tree” type thing to do though.

There is the old tales of maintaining small fires under the oil pan to warm it up.
I've had 12volt cars with 6 volt starters. 2000 degrees below zero and they spin right up. I've also put pans of embers underneath the car the whole under hood heats up. But that one is scary.like is oil going to drip and start a big fire? You burn charcoal to embers put it in a cake pan and slide it under the middle of the engine compartment under the car.
 
Last edited:

BigT

Member
Joined
Oct 17, 2024
Posts
32
Reaction score
58
Location
Selah, WA
First Name
Tim
Truck Year
1978
Truck Model
Scottsdale K20
Engine Size
350
Before fooling around with block heaters, you need to get the choke sorted out. Zero degrees is not that cold.

As mentioned, make sure the battery and cables are in good condition. If the engine cranks slow, it’s not going to want to start.
Back in high school, when I drove my 64 Chevelle every day, I put a Massey-Ferguson diesel tractor battery in it. I don't remember how many CCAs that thing had, but it was made to crank a cold diesel equipment engine to life in the dead of winter, and it would spin that poor 283 like it was a toy!! Damn thing lasted 12 or 13 years, too. It even had a little green LED in a window that would tell you if it was charged up or not. I wish batteries were made like that now.
 

Keith Seymore

Full Access Member
Joined
Jul 13, 2015
Posts
2,881
Reaction score
9,142
Location
Motor City
First Name
Keith Seymore
Truck Year
1987
Truck Model
R10
Engine Size
4.3L
Most reliable and easiest to install are soft plug heaters. Directions will instruct which one to install it in. Remember GM installed them from the factory.
RPO K05 = block heater

We used to use them to heat our water for coffee back in the remote areas of the plant.

K
 

Latest posts

Forum statistics

Threads
44,157
Posts
950,599
Members
36,273
Latest member
dannyphx
Top