Clicking noise

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,038
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
1978 K10, 350, 4sp, 205, 4" lift, 33s. Clicking is motion related, more so as a tire rotation, starts about 10 mph as a slow click and will gradually speed up. At 20 mph I can swerve left and right, as the left side loads (swerving right) the clicking will stop or slow down, as the right side loads (swerving left) the clicking will speed up.

Best way to describe the clicking, imagine you have a bearing that has balls in it, say 10 and you are missing 4, so as the bearing rotates the ball will fall and click as it hits the next ball. If that makes sense.

My experience with wheel bearings if load bearing noise goes away that side has your problem. But not get noisier if its unloaded.

I've thought of the center caps and trim rings (rally wheels) but really don't think that is it because it wouldn't make the noise just going straight down the road unless the tires were really low psi. BFG All-Terrains are at 32 psi and have been since owning the truck. Center caps are tight and lug nuts are as well. Rear left tire is missing one wheel stud and others are tight.

Any helps from you folks would be great.
 

bedwards

Full Access Member
Joined
Nov 12, 2016
Posts
192
Reaction score
156
Location
Adger, Al.
First Name
Bryan
Truck Year
1985
Truck Model
c10 Silverado
Engine Size
305
are your valve stems long and tapping your trim rings?
 

Blue Ox

Turning Diesel Fuel Into Fun
Joined
Mar 27, 2018
Posts
5,256
Reaction score
12,184
Location
LI-NY
First Name
Derek
Truck Year
MCMLXXXV
Truck Model
K20HD
Engine Size
6.2L
Interesting. Mine ticks at low speeds, particularly in turns. It sounds like ball bearings in the hubcaps. I'm thinking the steel wheels may be getting tired. Now that you mention it, I'll have to listen to it now that I have the Aluminum wheels on it and see if it's still there. I'm waiting to see what you find.
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,038
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
are your valve stems long and tapping your trim rings?

Interesting thought, I certainly didn't think of it. I will look at them to see if they are close the trim rings.

Interesting. Mine ticks at low speeds, particularly in turns. It sounds like ball bearings in the hubcaps. I'm thinking the steel wheels may be getting tired. Now that you mention it, I'll have to listen to it now that I have the Aluminum wheels on it and see if it's still there. I'm waiting to see what you find.

I did buy these rims / tires about 2 years ago, used of course. I think I'll pull the wheels and look for cracks around the lugs and welds if the centers are welded (I don't remember), I have a hard time believing that steel wheels can crack but it does happen.

This click really doesn't sound like a hard metal click though, almost like a tinny click or pot metal type click. What gets me is it speeds up when its unloaded and goes away when loaded.
 

hatzie

Full Access Member
Joined
Dec 6, 2011
Posts
567
Reaction score
459
Location
NH
First Name
David
Truck Year
1976
Truck Model
k20
Engine Size
6.5
Bad needles in the outer Universals in the axle? Similar to bad CV joints... I always thought of this as a snapping and popping noise. but...

The needle bearings around the end of the axle stubs inside the spindles can make ticking a noise when they're on their way out as well.
 

Blue Ox

Turning Diesel Fuel Into Fun
Joined
Mar 27, 2018
Posts
5,256
Reaction score
12,184
Location
LI-NY
First Name
Derek
Truck Year
MCMLXXXV
Truck Model
K20HD
Engine Size
6.2L
I did buy these rims / tires about 2 years ago, used of course. I think I'll pull the wheels and look for cracks around the lugs and welds if the centers are welded (I don't remember), I have a hard time believing that steel wheels can crack but it does happen.

This click really doesn't sound like a hard metal click though, almost like a tinny click or pot metal type click. What gets me is it speeds up when its unloaded and goes away when loaded.

Mine are 8 lug and there's no cracking that I can see anywhere, but they are riveted. After over a quarter of a million miles it could just be things starting to loosen up. Can't say I remember any noises from the alloys, but I usually don't pay that much attention either. I'll try to give a listen next time I drive the truck.
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,038
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
Bad needles in the outer Universals in the axle? Similar to bad CV joints... I always thought of this as a snapping and popping noise. but...

The needle bearings around the end of the axle stubs inside the spindles can make ticking a noise when they're on their way out as well.

I did think of that and did not investigate much further as the hubs were unlocked. I did rotate the tires when I jacked it up, locked and unlocked the hubs to see if the axles were turning and not turning. I mainly checked to see if the spindles were loose, right side had some wobble, so I tightened that side up but the left side had no play so I didn't open it up and take the wheel hub off.
 

hatzie

Full Access Member
Joined
Dec 6, 2011
Posts
567
Reaction score
459
Location
NH
First Name
David
Truck Year
1976
Truck Model
k20
Engine Size
6.5
The solid front axles are essentially full floating axles. The axle stubs stay still and the spindles rotate when the hubs are unlocked.

Lock the hubs and see if the noise goes away anyway. Prolly won't change
 
Last edited:

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,038
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
The solid front axles are essentially full floating axles. The axle stubs stay still and the spindles rotate when the hubs are unlocked.

Lock the hubs and see if the noise goes away anyway. Prolly won't change

I am aware of that, but didn't think about driving with the hubs locked. Good point.

Sadly, on my drive home, I had NO clicking, so now its intermittent. WONDERFUL! Looks like I have to wait until Sat. to investigate, I out of town until then.
 

rt66paul

Full Access Member
Joined
Apr 16, 2016
Posts
230
Reaction score
109
Location
California
First Name
paul
Truck Year
1991 suburban
Truck Model
2500
Engine Size
7.4
Do you have any jokers at work or in the neighborhood? Ball bearings, marbles, or even a couple of pebbles in your hub caps will drive you nuts.
 

elcamman50

Junior Member
Joined
Dec 7, 2016
Posts
19
Reaction score
23
Location
lakeside, california
First Name
charles
Truck Year
1979
Truck Model
c10
Engine Size
350
Pebbles in the hubcaps! Use to do that on Halloween in the early 60s when all cars still had hubcaps.
 

idahovette

Full Access Member
Joined
Aug 7, 2016
Posts
7,358
Reaction score
16,106
Location
Weiser Idaho
First Name
Perry
Truck Year
1975-1979
Truck Model
K20-K10
Engine Size
350
Pebbles in the hubcaps! Use to do that on Halloween in the early 60s when all cars still had hubcaps.
Neighbor kids out playing will put anything in hub caps or wheel covers. NO NOT MY KIDS!!
 

legopnuematic

Licensed Junk Dealer
Supporting Member
Joined
Oct 27, 2016
Posts
2,618
Reaction score
6,906
Location
MO
First Name
Spencer
Truck Year
1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
Truck Model
Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
Engine Size
225/6, 350 c.i., 350 c.i., 5.9l Cummins
I did buy these rims / tires about 2 years ago, used of course. I think I'll pull the wheels and look for cracks around the lugs and welds if the centers are welded (I don't remember), I have a hard time believing that steel wheels can crack but it does happen.
Made it from Winnfield Louisiana to Saint Louis Missouri (600 miles) like this. Tires were from 2007, so I'd assume its had been broken for a good part of that time. Both of the overload springs were busted in half, rear u joint had a 1/4 inch play in the yoke. Front tow hook ripped out of the frame, everything caked with mud.
You must be registered for see images attach
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,038
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
Yeah, that's not a good sign.
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,038
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
So... I've pretty much pulled the hubs apart to the last bolt, locked the hubs, checked the drivelines, even checked the rear brakes. Nothing showing any signs of wear, loose, broken, etc. Again this noise was intermittent. Today I got in to go home from work, heard the clicking, and for whatever reason I looked at the 4wd shifter and thought, "gee that's close to the console" yep, I was in 4HI. I'm an idiot, I think my son is playing games with me again. Time to put a coat hanger on his driveline. grrrrr.
 

Forum statistics

Threads
44,423
Posts
957,414
Members
36,769
Latest member
Bowtie72
Top