Am I Cursed by the Carburetor Gods? Or do I just suck with Carburetors?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

RecklessWOT

Full Access Member
Joined
Feb 20, 2015
Posts
2,556
Reaction score
4,764
Location
New Hampshire
First Name
Kevin
Truck Year
1987
Truck Model
V10 Suburban Silverado
Engine Size
350 TBI
You said the vacuum advance is still attached but "sometimes it likes it and sometimes it doesn't". Is your timing just all sorts of messed up? I'd unhook that and just set it somewhere conservative.
 

jjester6000

Full Access Member
Joined
Aug 24, 2019
Posts
882
Reaction score
2,459
Location
Illinois
First Name
Jack
Truck Year
1974
Truck Model
C1500
Engine Size
250
You said the vacuum advance is still attached but "sometimes it likes it and sometimes it doesn't". Is your timing just all sorts of messed up? I'd unhook that and just set it somewhere conservative.
I tried that, and it ran good again, then didn't, then decided it wanted to flood out, then wanted to lean out, then caught fire, then I hooked it back up, and it ran good again, then it wanted to lean out, then flooded, and caught fire, then it wouldn't even start.
(Are you starting to see a pattern?)

Anyways, I put a whole brand new distributor in it last year and used it in th new motor as well. The dwell and timing are perfect, and when it does run good, it purrs like a kitten.
 

Dmack

Full Access Member
Joined
Mar 13, 2019
Posts
334
Reaction score
437
Location
Central OR
First Name
Dave
Truck Year
1983
Truck Model
K20
Engine Size
350
I had a condenser go bad years ago, which caused intermittent problems of rough running and backfiring. Loose mount\connection or an internal issue. Cheap and easy to swap out. Just a thought.
 

jjester6000

Full Access Member
Joined
Aug 24, 2019
Posts
882
Reaction score
2,459
Location
Illinois
First Name
Jack
Truck Year
1974
Truck Model
C1500
Engine Size
250
SHE LIVES!!!.
You must be registered for see images attach

I stuck the new carb on, and it started right up and ran really good. I don't know for how long though.
You must be registered for see images attach

Here's where I welded the linkage pieces from one of the old monojets on.
You must be registered for see images attach
 

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
4,192
Reaction score
8,030
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
Well there's your problem, you're missing a whole bank of cylinders! Don't even contemplate a Holley EFI, you think you got problems now.
 

medicmudder

Junior Member
Joined
Apr 24, 2012
Posts
2
Reaction score
0
Location
Ward
First Name
Tony
Truck Year
1986
Truck Model
c10
Engine Size
350
Morning this may sound crazy but check the fuel pressure I had the same issue no matter what I did it still had the issue the fuel pump was putting out to much fuel put a pressure regulator worked great !!!! Check the fuel pressure!!!
 

Copymutt

Full Access Member
Joined
Jan 17, 2020
Posts
222
Reaction score
674
Location
Colorado
First Name
Jim
Truck Year
74
Truck Model
K20
Engine Size
350
Bad ignition wires can cause cross fire when they get close to each other. Ck. for deterioration and routing away from each other.
This would most likely be intermittent.
 

olnick

Full Access Member
Joined
Feb 7, 2019
Posts
52
Reaction score
29
Location
Milford NH
First Name
Nick
Truck Year
1978
Truck Model
c15
Engine Size
1982 350 4 bolt mains
I'm with Dmack ! Installed new points/condenser did a major tune up sat all winter then had issues like yours! I KKNEW IT WAS THE CARB!!! finally got sick with it running like crap all the time. Put the O scope on it and Damn primary wave for was all wrong. The new condenser was bad my coil was kicking back 600 volts intoo the primary. I replaced the condenser with one I had for my Bug that was 3 years ago. Runs like a champ and the POS carb is still on there running smooth i did not touch it after the ccondenser replacement But I knew it was the carb,!!!

OLNICK
 

seniorbear69

Member
Joined
Oct 1, 2020
Posts
49
Reaction score
19
Location
rayleigh essex uk
First Name
steve
Truck Year
1984
Truck Model
c20
Engine Size
350
check the carb to manifold gasket .make sure it seals the carb to manifold no open air ways .dont ask how i descoverd this !
 

75Monza

Full Access Member
Joined
May 5, 2017
Posts
1,362
Reaction score
2,843
Location
Colville, Washington
First Name
Jeremy
Truck Year
1980, 1982, 1985
Truck Model
K30, K20, K20
Engine Size
454, 383, 350
I had real similar luck with an old 230 in a 65 nova I had, single barrel. Seemed like nothing I did could get it to run right over idle...if I could even get that. Original carb, rebuilt it, would go too rich to where exhaust manifold would glow from exhaust overtemp just trying to get damn thing to run. Replaced whole ignition with no luck, adjusted valves, fuel delivery to carb checked out, couldn't find any vacuum leak. Leakdown test on cylinders was not the greatest. I never did dig into the timing chain, but suspect something was not quite right in there because would end up raw fuel dribbling out exhaust sometimes. Finally end up selling it since it was a free car and 4 door just to get it out of my hair and give me time to mess with my 2 door 64 instead, lol. About all I figured was v-8, 4 barrel and HEI was alot easier to troubleshoot than that damn setup for sure. If engine mechanical is sound, it's basically spark or fuel problem that I would start with spark, verify complete ignition, then work on the fuel. Since an engine is just an air pump, verify no intake restrictions and same with exhaust since I've had a rat's nest inside a muffler before blocking off air flow so severe backpressure.
 

rt66paul

Full Access Member
Joined
Apr 16, 2016
Posts
230
Reaction score
109
Location
California
First Name
paul
Truck Year
1991 suburban
Truck Model
2500
Engine Size
7.4
Is this the six with the incorporated intake manifold? The fix is to use an older head and manifolds, those heads crack and do suck air. They can do it intermittently and drive you crazy. The fact that you have a burned exhaust valve could show a bad vacuum leak, you are running too hot.
I think it is a combination of things, replacing a carb on a vehicle with other problems does not fix the earlier problems.
 

Latest posts

Forum statistics

Threads
44,168
Posts
950,770
Members
36,283
Latest member
Cantrell299
Top