350 dies when warm and won't start

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

andrew-75c10

Junior Member
Joined
Jun 20, 2020
Posts
17
Reaction score
6
Location
San Diego
First Name
Andrew
Truck Year
1975
Truck Model
C10
Engine Size
350
Background: I've been working on my 75 C10 that I got from my grandfather. So far I have replaced the fuel tank, fuel pump, and rebuilt the carb. A couple months back I bought a tach and got the cold idle and warm idle RPMs dialed in. I also bought a vacuum gauge so I can get the idle mixture screws dialed in. However, a few minutes after my truck warms up it dies I cannot restart it.

At first I thought this might be a cooling problem (none of my gauges work but one problem at a time). I was talking to my dad and he said I should really changed the coolant either way. So today I did my first coolant flush. I was expecting my coolant to look like dirt after watching how-to videos on youtube. It still had some green color, but it wasn't as bad as I imagined.

After replacing the coolant, I hooked up my vacuum gauge to the brake booster line. When I start my truck cold, I get 20 PSI of vacuum. As it warms up, the vacuum drops to 15 PSI. If I turn off my engine at this point, it won't start again. If cooling isn't the problem, I'm stumped.

After reading the forums, I was going to try:
1. Get a clear fuel filter so you can see if the carb is getting gas
2. Get a spark tester

Hopefully I can figure this one out so I can get the rally wheels that I bought installed :)
 
Last edited:

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,451
Reaction score
8,698
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Forget both of those items look down the throat of the carb open the throttle by hand fuel should squirt 2 streams like a squirt gun down the throat, if it does it's not a fuel problem. If it doesn't then wecan start trouble shooting fuel. The inline spark tester will light with a lightning bug fart, but not enough spark yo start an engine. Take a spark plug open the gap to about .080 clamp it in a jumper cable clamp the jumper cable to ground put a plug wire on the plug and crank. That will tell you if you have spark. Post results.
 

80BrownK10

Full Access Member
Joined
Oct 22, 2019
Posts
1,878
Reaction score
1,247
Location
Greenwood, SC
First Name
Nate
Truck Year
1980
Truck Model
K10
Engine Size
350
Is your coil good? Ignition module. Both if get hot could be failing. But I wouldn't think it would happen every time, every now n then maybe.
 

80BrownK10

Full Access Member
Joined
Oct 22, 2019
Posts
1,878
Reaction score
1,247
Location
Greenwood, SC
First Name
Nate
Truck Year
1980
Truck Model
K10
Engine Size
350
Yes like said look down the crab when you open the throttle. Quick test if it's fuel issue just take some carb cleaner and spray into the carb for 2 seconds then try to start it. If it fires you ha e a fuel issue if not, probably something else, like ignition related.
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,266
Reaction score
2,210
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
First question- what carburetor are you using? If it’s the original Quadrajet, what is the number on the side, and what rebuild kit did you use?

Buying Quadrajet rebuild kits can be confusing, since GM switched to a newer style carburetor on the trucks later than they did on cars. If you buy a rebuild kit for a 1975 Quadrajet it will probably be for a 1975 car, which is the wrong kit for a 1975 truck. You must go by the number on the Quadrajet, not the year of the vehicle. For example, the original carburetor on my ‘75 K25 is number 7045583 YZ 3454, which was used on HD emissions trucks.

Bruce
 

andrew-75c10

Junior Member
Joined
Jun 20, 2020
Posts
17
Reaction score
6
Location
San Diego
First Name
Andrew
Truck Year
1975
Truck Model
C10
Engine Size
350
I have some starter fluid, and after it warmed up and had trouble starting, I spraying some in there and the engine would turn over. I started looking for fuel problems, and low and behold I found my accelerator rod was bent. I'm really not sure how this happened, but maybe I need to find a new one. I straightened it out the best I could for now.

My truck seems to idle fine now, although I noticed the vacuum fluctuates between 9-13 mmHg. I'm guess it means I have a vacuum leak, so on to the next problem.

Here are some pictures of before (I already took it after the carb) and after (installed back on the carb).

You must be registered for see images attach


You must be registered for see images attach
 

andrew-75c10

Junior Member
Joined
Jun 20, 2020
Posts
17
Reaction score
6
Location
San Diego
First Name
Andrew
Truck Year
1975
Truck Model
C10
Engine Size
350
I spoke too soon - made it a few times around the block then wrote up this post. I tried to go around the block again and it did not make it.
 

Raider L

Full Access Member
Joined
Sep 1, 2020
Posts
1,892
Reaction score
1,001
Location
Shreveport, LA
First Name
William
Truck Year
1974
Truck Model
C10
Engine Size
355
@andrew-75c10,

Q-jets are nortorious for needing perfect vacume. I had these problems and it could very well be a vacume leak internally. Make sure if you have any rubber caps or rubber hoses attached to it check them for cracks or looseness of a hose. Replace rubber caps and any hoses that look suspitious.

Otherwise i am leaning towards the coil. Except the coil isn't going to be getting "warm" like the carb is. So it's probaby the Q-jet. Want to solve the carb problem? Buy a Holley!!
 

idahovette

Full Access Member
Joined
Aug 7, 2016
Posts
7,270
Reaction score
15,874
Location
Weiser Idaho
First Name
Perry
Truck Year
1975-1979
Truck Model
K20-K10
Engine Size
350
@andrew-75c10,

Q-jets are nortorious for needing perfect vacume. I had these problems and it could very well be a vacume leak internally. Make sure if you have any rubber caps or rubber hoses attached to it check them for cracks or looseness of a hose. Replace rubber caps and any hoses that look suspitious.

Otherwise i am leaning towards the coil. Except the coil isn't going to be getting "warm" like the carb is. So it's probaby the Q-jet. Want to solve the carb problem? Buy a Holley!!
This is not necessarily the answer, just get your Quadrajet set up correctly and you may be fine!
 

Forum statistics

Threads
44,168
Posts
950,804
Members
36,286
Latest member
goodwrenchca
Top