carburetor

  1. legozombie

    Engine Stalling - Bad EVAP/Charcoal Canister?

    I tried doing some research and didn't find anything relevant so here is a new thread. There is a question at the end, I am just trying to give as much back story as I can. Without further adieu... So last week I was changing out the fuel sender on my stock 350 sbc QJet-M4M3 1983 K20 p/u and...
    • legozombie
    • Thread
    • 350 canister carburetor charcoal canister evap fuel delivery fuel issue quadrajet vapor canister
    • Replies: 29
    • Forum: Carb Fuel Systems
  2. 77Matt

    Passing CA Smog help - High HCs

    I have a 1977 GMC 5.7L 350 given to me from my dad. It passed smog no problem less than a year ago for the title transfer. Now, it failed CA smog due to high hydrocarbons (3485 ppm @ 15MPH and 1350 @ 25MPH). Also noteworthy is that the technician said the crankcase ventilation hose that feeds...
  3. L

    C10 1985 305 stalled and now won't start and choke won't come on

    I need help to start my truck again,I was driving with my brother to the park but once I started going up hill it started to sputter like if it wasn't getting any gas then it died. I walked to get my other truck so I could pull it and when I got back I tried to start it but only stayed on for a...
    • Luisd02
    • Thread
    • 305 1985 longbox 2wd c10 carburetor choke light gas wont start
    • Replies: 1
    • Forum: Tech Discussion
  4. klarster

    '85 K20 350ci died out on the road not getting fuel to carb, replaced fuel pump and now not getting fuel to pump

    Hi folks! First post in this group so I'll try to cover all the bases in an effort to get the best outcome. Bought an '85 K20 with factory 350 and manual tranny off a college kid a couple months ago with intentions to drive while I do some work on my Jeep to get it roadworthy again, then begin...
  5. Mason Lawley

    Rebuilt Quadrajet

    Re-installed the quadrajet after doing my first carburetor rebuild. The first video is of the truck running without a foot on the pedal at all. Seems to idle high for awhile, and then eventually dies. Any help to point me in the right direction is much appreciated. Pictures of the carb at the...
  6. M

    Edelbrock 1406 Jetting

    I've been looking at a few forum posts looking for what people have found with tuning and jetting their carbs, and maybe I'm confusing information, but some people seem to be maybe using different jets for the secondary side? Unfortunately working long hours and the car being parked for the...
  7. Isaac nickerson

    Electric choke question

    Hey yall, both me and my buddies electric chokes on our k10 and c10 were working great until we both took our carbs off (holley 4160) and when we but them back on we both have the following problem. I go to start the truck and it starts fine and the high idle works and the choke opens about 75...
  8. trentdoubledown11

    On Start Engine Revs to Infinity and does not idle

    1984 C10 305 New 4 barrel quadrajet (although it sat for 5 years) New Fuel Pump New dual 16g tanks New Sending Units and fuel lines (between tanks and tank switcher) About 5 years ago the truck died while driving. I replaced the fuel pump and fuel filters (on carb and 2 back at the tanks)...
  9. chevyninja350

    carburetor size on a 350

    I need help. I know stock Chevy 350s are happy with 650 CFM carburetors. That being said I have a 750 Edelbrock 1411 on my non bored over 350 9.93:1 compression that is far from stock. It has an Edelbrock dual-plane intake, A lopey 510/520 lift cam (2200-5800 RPM) and aftermarket vortec heads...
  10. 7

    Carb not squirting fuel and fuel filter holds half fuel

    I have a 79 gmc c6000 with a 350 in it. The truck is not starting... it turns over but will not engage in starting. The carb is not squirting fuel and I checked the fuel filter and it’s only halfway full of fuel. I’m not sure if fuel is not coming out of tank or if there’s issues from the filter...
  11. 8

    Engine cuts off when I press on the gas pedal

    I have a 78 k10 with a 350. For some reason, when I press on the gas, the engine cuts out. Is this caused by the fuel/air ratio, the choke, or something else?
  12. G

    Quadrajet Adjustment Question

    I currently have my idle screw all the way out , such that it is not tensioning the cable whatsoever or putting any pressure on the little plate at the end of the screw. my question is , am I supposed to tune the air/fuel mixture with base (minimal) tension on the cable (where the idle screw...
  13. caleb chapdelaine

    350 small block build

    I just got a block for a 350 sb, looking to build it to where it’ll put out some decent power for a k10. It’s gonna be a budget build. What are some good heads and etc won’t break the bank, thank you.
  14. Tanner_Shany24

    Need help with very bad sputter with 83 k20 bbc 454.

    Hey guys, recently bought a 1983 k20 with a bbc 454 in it. I like the truck a ton, but it has its flaws, and a lot of them haha. I am 18, and while I have worked on motors my whole life, this is the first carbed motor I have owned, so I am kind of new to the carb game and just want to get some...

Latest posts

Forum statistics

Threads
44,411
Posts
956,913
Members
36,729
Latest member
Massimo
Top