Search results

  1. hey mister

    350 TRANSMISSION SPEEDOMETER GEAR HOUSING

    Maybe a Bearing seal puller. Or a slide hammer with the hook end.
  2. hey mister

    Owners manuals for sale

    How much would you like for it ?? And please include shipping to: Kent, Ohio 44240
  3. hey mister

    Owners manuals for sale

    Ok. No rush. Thanks for repling & looking.
  4. hey mister

    Owners manuals for sale

    Might you still have the 1978 owner's manual? Thanks.
  5. hey mister

    Dingleball Hones

    When I rebuilt my GoldWing engine, I contacted Total Seal to get the info on cylinder finish. They guided me on grit and technique to get the correct crosshatch pattern. Grit is only half the equation. Crosshatch pattern angle is just as critical for break in. I would contact the ring mfg and...
  6. hey mister

    TransGo shift kit install...

    Yep, that was the $30.00 one...lol
  7. hey mister

    TransGo shift kit install...

    Update: Addendum I just couldn't get the dripping to stop. So, I went to Summit to check out my gasket options. I did find a composit one , but man I almost pulled the trigger on the $31.00 one that almost promised to install itself. It was hard to pass on that one. However, while I was...
  8. hey mister

    TransGo shift kit install...

    Ok...I'm not the mechanical whiz-bang kid I fancied meself to be... After tightening, retightening and thrice-tightening them tranny pan bolts, the leaking continues. Honestly, I laugh every time I see it. Ya just can't make this up. I've lost count the number of GL1000 & 1100 engines I've split...
  9. hey mister

    TransGo shift kit install...

    Composite? What kind of composite?
  10. hey mister

    Summit Brand Headers???

    I see you already got your headers in. I put on a set of Summit's stainless with 3" collector. I wrapped them with the fiberglass header tape before install. I did use an inexpensive gasket and have had a slight leak, but when I pull the motor this summer to replace sesls and gaskets, I will...
  11. hey mister

    TransGo shift kit install...

    Oooo doggies...what a puddle, this morning. Grabbed a wrench and slid under. Them pan bolts were barely finger tight. I knew a cork gasket would compress a bit after initial run...no big deal. Just retorqued them. I'm sure I'll have to do it again after the next run. I had to last time I changed...
  12. hey mister

    TransGo shift kit install...

    I did go with the screen type.
  13. hey mister

    TransGo shift kit install...

    The first filter looked like this.
  14. hey mister

    TransGo shift kit install...

    Update: The local parts house ordered a trans oil filter and I went this morning to pick it up. Paid for it and started to drive away, but this little voice told me to take a look at it. So I opened the box and the filter was not square like the one I pulled out. The edge of the filter material...
  15. hey mister

    TransGo shift kit install...

    Thanks again. I really do appreciate the insight. Yea, I thought it was strange that the original balls could compress. But then, what better way to get a seal than to use a hard rubber ball to seal. I am familiar with the dk brown balls, but I don't have them. So I guess the steel one will...
  16. hey mister

    TransGo shift kit install...

    I still have the original balls. Are they supposed to be "compressable".? They are about as soft as a hockey puck. I do have 4 ceramic balls. I thought about putting them in, instead of steel. I just didn't know what kind of fluid induced impact they would encounter. Fortunately,it won't be...
  17. hey mister

    TransGo shift kit install...

    Initially, I wasn't going to tear into the tranny today, but it really got nice after lunch and nothing else was on the agenda. Got everything tore apart and springs swapped out. I couldn't believe it...The original 4 check balls are freaking plastic. Plastic! I mean, what could of possibly been...
  18. hey mister

    TransGo shift kit install...

    I had seen some videos of older guys talking about drilling holes and milling out slots to modify it for racing. Our goal is to use it to pull a 19' to 22' camper. I'm not looking for any wheel chirping or burnies...lol
  19. hey mister

    TransGo shift kit install...

    It's a TH350. The shift kit does not require removal. Only the valve body and govenor needs removed.
  20. hey mister

    TransGo shift kit install...

    Over the winter I picked a Quadrajet as an exact numbers replacement/backup. I called Cliff to get his kit and we got to chatting. I shared my intent for the Big10 and he suggested a TransGo 1&2 shift kit. Depending on the springs installed will dictate the personality; street or...
  21. hey mister

    GM Square Body Forum Decals

    This thread is over 3 years with no response. I'm guessing it has dried up. Go to Summit Racing. They have really kewl Suare body Tees. Sizes run small. I have to get next size up.
  22. hey mister

    Let’s see your memorabilia?!

  23. hey mister

    Air Filter Breather

    I don't think height is much of an issue. Even with the lid flipped over, I have at least 4" between hood and breather lid. I will let ya'll know when I hear from DVAP.
  24. hey mister

    Air Filter Breather

    Sounding cooler is always a plus...lol
  25. hey mister

    Air Filter Breather

    Thank you! I put in a request. Thank you!

Latest posts

Forum statistics

Threads
45,288
Posts
979,743
Members
38,303
Latest member
Elvis2025
Top