Search results

  1. Lugnut

    Need help, '86 C10 AC condenser insulator.

    I ended up finding mine on a '93 S10 in a junk yard. It was exactly the same part #. Good luck.
  2. Lugnut

    AC Compressor

    No problem, if it helps the OD is 7/8" with a 1/2" hole through it. You can go to your local hardware store and pick up a short pipe nipple and cut off the threads and cut the center to length for a few dollars and no one will know the difference.
  3. Lugnut

    AC Compressor

    The spacer on my '81 is 1.400" measured with a set of dial calipers. From the front of the compressor to the center of the belt groove is approximately 1.2" with an eyeball. Hope this helps.
  4. Lugnut

    '81 bolt in high hump and clutch pedal assy.

    I have a good NV3500 that came out of a '92 OBS that I am planning on using, so thats why I want a hyd. pedal assy. I know that are not know to be a strong transmission but it will be going behind a worn out 305 daily driver so I'm not to worried about it. That coupled with most of my wilder...
  5. Lugnut

    Spray vs Plastic Bedliner

    As far as the lower tie downs I used a u-bolt on the corners of the bed. I put a slight bend in them to make it a little easier to use. The rear ones I removed the taillight to gain access to the nuts. One of the best most useful things I’ve ever done to the truck.
  6. Lugnut

    '81 bolt in high hump and clutch pedal assy.

    Yes I am very interested. Thanks
  7. Lugnut

    '81 bolt in high hump and clutch pedal assy.

    I am looking for a bolt in high hump for an '81 c10 for a 5-speed conversion, and a clutch pedal assy. for a hyd. clutch set-up. Thanks
  8. Lugnut

    What have you done to your square lately??

    These are the brackets for the shorter radiator.
  9. Lugnut

    What have you done to your square lately??

    From what I have seen a lot of the factory non-air and manual trucks got a shorter radiator. My '86 is factory air with a A833 4-speed had the shorter radiator. The upper radiator brackets are L-shaped and the fan shroud is also different.
  10. Lugnut

    pin stripes

    Holley also sells kits for our trucks. I have used one kit from Holley it was a little less expensive than Phoenix Graphix, and it went on just fine and looked good. I have used a couple from Phoenix, I think they may have a better selection of colors, with no problems. I installed a kit from...
  11. Lugnut

    Question about headers

    Hooker is making cast iron manifolds that look pretty good and are supposed to flow a lot better than the stock ones. I haven't tried any yet but that is what I am leaning toward on my next engine swap.
  12. Lugnut

    Probably the worlds worst question… can any ID this.

    Windshield wiper delay module.
  13. Lugnut

    Need ideas for a modern steering wheel.

    Comfort Grip is the name of it, I'm pretty sure it is made by OER (Original Equipment Reproduction) but not 100 percent on that. 15" dia. and the overall dish is 3 7/8" including the adapter. I will say this, it sat out in the direct Georgia sun about 6-7 hours this past Sunday and while the...
  14. Lugnut

    Need ideas for a modern steering wheel.

    I installed one of these comfort grip wheels on mine about a month ago and so far I love it. If I remember right it was about $200 with the adapter kit and horn button. Very easy to install and horn works great.
  15. Lugnut

    Looking for a shift knob.

    I had a red 3 billiard ball on mine for a few years but the sun finally turned it pink. I bought this q-ball and had my son who works for a machine shop mill in my pattern on it. I have always liked the feel of the bigger billiard ball as a shifter knob.
  16. Lugnut

    Do aftermarket speaker mounts make 6x9's clear the cab?

    Thanks, no I had a buddy powder coat it with a crinkle finish black.
  17. Lugnut

    What have you done to your square lately??

    Thanks, it turned out better than I thought it would.
  18. Lugnut

    What have you done to your square lately??

    Thanks, it’s been a long process. This is a before pic.
  19. Lugnut

    What have you done to your square lately??

    I made a little more progress and can see the light at the end of the tunnel. I got to get a buddy to come over to help set my hood without scratching everything. I always use Felpro on mine, no leaks so far.
  20. Lugnut

    What have you done to your square lately??

    I made a little more progress and can see the light at the end of the tunnel. I got to get a buddy to come over to help set my hood without scratching everything.
  21. Lugnut

    What have you done to your square lately??

    Yes standard GM rally with no spacer. I have about an inch between the top of the tire and the inside lip of the wheel well trim.
  22. Lugnut

    What have you done to your square lately??

    Thanks, This one isn't going to get bed rails, but I have a red one that the previous owner took them off, so I might want a set for it. you can PM me the price. The front is a 235/75 on 7" rallies, not my choice of tire but they were brand new so I thought I would run them for a while. The...
  23. Lugnut

    What have you done to your square lately??

    I took it on its maiden voyage since I started the restoration. I still have a long way to go but made me feel a little inspired to keep going.
  24. Lugnut

    What Are They??

    Bed adjustment.
  25. Lugnut

    Do aftermarket speaker mounts make 6x9's clear the cab?

    I didn’t have any issues with mine.

Latest posts

Forum statistics

Threads
44,720
Posts
966,226
Members
37,392
Latest member
jimmy1986k5
Top