Search results

  1. Taylorb27

    84 c10 dual headlights retrofit?

    I have them in the box but the front end of my c10 is still apart for my ls swap lol and now with winter here it will be a few months more than likely!
  2. Taylorb27

    Fuel line question

    just here chiming In as another North Dakotan! Central here where 200 and 281 meet!
  3. Taylorb27

    Issues finding a th350 o ring kit?

    awesome thank you!! I googled everything BUT the word gasket lol I see this is for a power glide I assume I’ll need to find one for a th350 or are there the same amount of o ring seals and gaskets?
  4. Taylorb27

    Issues finding a th350 o ring kit?

    So admittedly I’m not the most knowledgeable when it comes to th350 rebuilds so my brother in law is doing my th350. He’s no pro but hes built more than I have. I already had clutches, steels, a shift kit and a thrown together seal kit from stuff I had laying around. Basically the only seals...
  5. Taylorb27

    84 c10 dual headlights retrofit?

    Ya I don’t think they’ll stick out that bad. The front will be blacked out like my buddies pickup and they aren’t super gaudy. They aren’t the exact same headlights but very similar
  6. Taylorb27

    84 c10 dual headlights retrofit?

    My 84 Scottsdale with the single headlights and marker lights below. My plan is to replace the headlight with a pair of black led h6054 with amber turn signals built into them and try to find either a light bar or other aftermarket light housing to fit in the market housing spot. It will...
  7. Taylorb27

    Carb line help. I'm so lost

    B goes to the charcoal canister. I think for bowl vapors
  8. Taylorb27

    Th350c rebuild or just re seal?

    Not sure if the trans tune has stop leak in it but it definitely did not sit long enough to swell any seals before it started leaking bad. I’m hoping it’s not as hot today so I can pressure wash the bottom of the pickup off and get started on taking the trans out so I can see what’s going on
  9. Taylorb27

    Th350c rebuild or just re seal?

    yes the condition of the bottom of the pan is a big factor in what I’ll be doing. what kind of damage would I be looking for? I guess I should mention that this happened just days after adding seafoam trans tune to it.
  10. Taylorb27

    Th350c rebuild or just re seal?

    So the front seal on my 84 c10’s th350 completely let go and is leaking trans fluid like mad. It started a block away from home when I gunned it and it’s been parked ever since. Now that I’ve got all my ls swap parts together I’ve decided it’s time to tackle the trans, question is should I...
  11. Taylorb27

    Intake manifold leak

    Are you sure it’s not gas leaking from the carb gasket? It looks wet all the way up to the carb. looks to be a factory manifold and probably not pulled recently so why would it start now? I don’t know just a thought
  12. Taylorb27

    Th350c major leak & future behind an ls?

    awesome! I’ve never dealt with a c before so wasn’t sure how much of an issue the tc seal was. Probably just going to order a good “stage 2 or 3” blah blah rebuild kit, do a trans go kit and try to find a 2200 stall converter that will work with lockup. thanks for the help!
  13. Taylorb27

    Th350c major leak & future behind an ls?

    So the th350c in my 84 c10 decided to leave a nice oil slick about 4 blocks to my house. Looks to be leaking from inside the bell housing as it’s leaking from my starter and somewhere on the driver side. Guessing the oring seal for the TC or a front seal? Anyway this is jumpstarting my LS swap...
  14. Taylorb27

    Anyone have any Jeep wj quadratrac experience?

    Seems the Jeep forum I’m on is dead on the wj side. Recently I picked up a 1999 Jeep Grand Cherokee 4.7l with the full time quadratrac posi 4wd system. The best part is it was FREE! Body is great, no rust at all.. it was driving awesome, started right up, has an exhaust manifold leak but I’ll...
  15. Taylorb27

    Need some help bringing back an 85 C10

    I’m almost certain it’s an orange wire. Yours will be hooked to a plug that has a wire going from the firewall by the passenger side valve cover. It’s the harness for esc but you can get rid of that if you are using a regular hei.
  16. Taylorb27

    454 Big Block Chevy Build

    Idk what they have for budget oriented aluminum heads but I’d try to fit them in a budget. Aluminum heads are lighter but more importantly will allow you run a little higher compression on pump gas.
  17. Taylorb27

    454 Big Block Chevy Build

    Here’s a stock crank, rods, block 454 I helped a good buddy of mine set up and put together. trick flow aluminum 113cc heads, 22cc dome pistons, hydraulic roller cam 225/231 112lsa. Figured to be around the 9.7:1 compression area. It’s in his 81 k10 and running with a decent built th350...
  18. Taylorb27

    TBI to Carb swap

    If you swap to a pre 87 manifold to a motor with tbi heads you will need to drill out or slot the middle 4 bolt holes on the intake. Tbi heads have a different bolt angle. I agree with diagnosing and keeping the tbi.
  19. Taylorb27

    New Leaf Springs...How did I goof it up?

    If they are the heavy duty springs they are 56” I believe. Non hd springs are 52”. I could be wrong on those numbers though I’m fairly certain that’s where your problem lies
  20. Taylorb27

    New blower motor shot??

    I guess I’m lucky I was only having heater blower issues haha! although the junkyard 5.3 I’m planning to throw in and boost is showing it’s mileage more the farther I dig in, close enough?
  21. Taylorb27

    New blower motor shot??

    Just a quick update, I guess I got unlucky on the new parts lottery the first time. Parts store replaced it and now this one blows nice and quietly.
  22. Taylorb27

    Longbed Inspiration needed

    I just put some 17x9 +20mm vision wheels on my 84 c10. 275/55r17 tires. It’s at stock height right now but I will be doing and axle flip in the Back and cutting 2 coils off the front until I get sick of the rough ride lol.
  23. Taylorb27

    Wheel lip rubbing on UCA’s

    So it’s actually rubbing on the ball joint plate. All I did was spent a few minutes with a green rolock disk and I’ve got an 1/8” of clearance now
  24. Taylorb27

    New blower motor shot??

    I just went out to flip the fan on quick and now it’s a constant high pitched squeal just like every bad blower I’ve ever heard. Hit the blower a couple times and it changed its pitch. So I guess I’m going to try a second one from the local parts store. I have a video but I’m not sure how to...
  25. Taylorb27

    New blower motor shot??

    So I’ve had a terrible, very loud squealing noise coming from what seems to be the blow motor. It’s not a constant squeal but when it chirps it hits loud and hard, can here it a few blocks away lol well I figured i just needed a new blower and that was that. Put the new blower in tonight and...

Latest posts

Forum statistics

Threads
44,552
Posts
960,575
Members
37,027
Latest member
chris501
Top