Search results

  1. RanchWelder

    98' Vortec Block, Timing Cover and Balancer Spacing Questions.

    My new engine is a 98' Vortec Block. Noticed the Harmonic Balancer is identical the one I used previously on my 1994 Casting SBC 355HO. Read the reluctor wheel causes the Balancer to move out 1/8" from the crank timing gear. Other than that they are the same. My previous engine had the...
  2. RanchWelder

    The Cone of Shame

    65' C-10 Look at that face... It's not a factory short-bed. The dog makes the photo and the truck is cool. Dragster?
  3. RanchWelder

    Small diameter distributor, 5.7L

    If you have a good tube with threads not stripped out the top plate, I am interested in purchase or trade for something I might have you want. I have working internal parts, gear, coil and ignition pack. Just looking for a good tube with plate, or whatever you have laying around that might be...
  4. RanchWelder

    OEM Small cap distributor main shaft tube, top plate, good threads, or better...

    My guts are good. The 7 wire ignition module is new. Same with my coil and reluctor wheel and flying magnets. If you can spare the main tube with threads or have a good working unit for parts, replacement, please email me with a price shipped. Need to turn the engine over and verify the mains...
  5. RanchWelder

    Disability or electric wheelchair's, motor vehicle ramps, lift's, elevator's, stair climber's

    Email me if you have a request for service vehicle or disability assistance products. We have several bus ramps in perfecto near perfect condition. Six stair climbers, slightly used in great condition. Cranes and lifts of every kind. If you have a friend who's life could be made easier with a...
  6. RanchWelder

    87' Blazer Short Bed 3/4 Ton 5th Wheel Conversion.

    Here's the Demco getting nstalled to the Blazer bed: Side Plates for the Frame: (Spot welds have not been hit with a grinder yet... It's very tough to get into there with a bad back and old man eyes. The wind was stealing my argon. it's good). All the rivet welds are behind the fuel lines...
  7. RanchWelder

    5th Wheel RV in MT for living quarters.

    Hey Mountain men and ladies! Hello to the Rolling Hills and Parie dwellers! Looking for a good clean older-ish RV for me and the Bat Cat to live in. Much obliged for your kind consideration!
  8. RanchWelder

    4L80E fresh rebuild, no reverse.

    Before I remove the 4L80E to verify the pump pressure regulator valve is not obstructed, I'm looking to verify the NEW B solenoid is not stuck open. Anyone with a proven method to test (besides the continuity test), which they both passed? How do you test the solenoid valve is actually not...
  9. RanchWelder

    Multiple Battery types and the danger of diode damage with modern batteries mixed with Lead Acid and OEM alternators.

    Bought a Power-Master 3 years ago because of charging adjust-ability, L/A vs AGM vs Lithium. Had no idea what was going to be removed from the shelves because of EPA or lack of manufacturing. PM is rated at 200 amps. Never thought the idle voltage was a concern, TBH. Can see how it matters. Dim...
  10. RanchWelder

    ***Hitch Procured*** Thread closed

    Looking for options and advice on selecting and operating a "slider 5th wheel" on a shortbed. Building my own frame mounts, plan on using 20K rails 20K sliders, 16K 5th wheel head, with 10 degree gimbal side to side. If you have anything in very good to excellent shape or advice on what to...
    • RanchWelder
    • Thread
    • fifth hitch shortbed slider towing wheel
    • Replies: 0
    • Forum: Wanted
  11. RanchWelder

    Electrical dash wiring / wire color issues.

    I'm rewiring a custom dash in my 1987 Blazer. I'm used to just using my Amprobe with a pair of wire spikes and verifying these things as I need to. Without power with so much of the dash opened and with thin gauge dash light kit in a custom aluminum entire dash console and dash board, I'm in...
    • RanchWelder
    • Thread
    • 14-bolt 4l80e cluster dash electrical fans fuel system gauges relays wiring
    • Replies: 6
    • Forum: Electrical & Audio
  12. RanchWelder

    Ice Cube Fuse Fail

    This thread is supposed to show what can go wrong and how anyone without a clue can make a wiring mistake. It also shows how a person can write a review showing exactly how he screwed up and hasn't a clue what he did wrong. The story starts out with a link for a reliable Eaton Fuse Holder. The...
  13. RanchWelder

    1956 Chevrolet Bel Air Coupe

    Next door neighbor's got one of the Tripplets. It's dusty from the winter and hasn't been polished yet. As you can see, the lines are very clean. The Odometer shows a slightly lower set of numbers, slightly out of alignment at 34832. The chrome is all mint. There's more pictures, if you...
  14. RanchWelder

    Square Tow Truck

    Hell Yah Buddy.
  15. RanchWelder

    TIS 20-Inch x8.5-inch Chrome Wheel for sale. New Mint 6 lug. Fits Dodge and Chevy.

    Please measure the center hole and ceter to center stud spacing. Max Tire Diameter 33-inch: Very clean. As NEW, never mounted. Buyer pays actual shipping. Reasonable offer's be SquareBody email only. Do not post any offers in this thread please. Insured delivery by UPS or USPS only...
  16. RanchWelder

    1978 / 1980 Pontiac Service Manul/Service Manual Suppliment Dealership Repair Manuals.

    These manuals are 100% brand new, zero defects, no fingerprints, never used never creased. If there's a dog eared page, it probably came that way from the publisher. Please email me, instead of claiming them on this thread. I'll ship in 21 days, after everyone makes an offer and gets a chance...
  17. RanchWelder

    Proportioning valve for 13" Brakes: 14-Bolt swap

    Swapping my 10 bolt for 14 bolt FF rear axle. My master cylinder and rear brakes are 1/4". Anyone with enough spare 3/16" tubing, larger style compression nuts and/or a known good working proportioning valve, please pm or email me? The compression valve is my main priority. We have no bone...
  18. RanchWelder

    WTB Shifter *** Thread Temporarily Reopened for SquareRoot *** Shifter Aquired.

    I'm swapping a 4L80E and could use a notched shifter, so it doesn't slip out of gear on dirt raods. Doesn't have to be show quality, just function without major rebuild or fitment issues. I'm planning on installing the Sonnax late model short shaft, which will allow for the shift cable to mate...
  19. RanchWelder

    99' K2500 Steering Column in 87' Blazer?

    Not so much concerned with the wiring aspect. Got pig tails for the 99' wheel/harness. Most likely upgrade the anemic wiper system in the 87' to the newer style, with the intermittent in the motor housing. So not concerned with wiper wiring in the swap. No cruise in the Blazer, no worries...
  20. RanchWelder

    Identifying GM Transfer Cases: Show us in pictures what you have with measurments and Adapters.

    My point in starting another thread on transfer case compatability, is because I'm in the process of adapting for my 87' Blazer to a modern electronic transmission with a stand alone and the 355HO TBI. I own a 1998 LH 355HO with the crankshaft sensor, so I can possibly use the 0411 ECM, which...
  21. RanchWelder

    Cam Grinding Service

    Check the video out.
  22. RanchWelder

    *****Closed****** 1999 GMT400 K2500 Suburban Part Out

    Reasonable offers please. This truck in the silver exterior/tan interior. Leather seats, all three rows, 75/25 back seat, electric/heated, with pig tails m/f Front driver's seat shows 2-3" splits, where the cushions start to wear out from getting into and out of the driver's seat. Very minimal...
  23. RanchWelder

    AM General M998 HMMWV 4 Door Hard Top w/Truck Body

    Item Number 10580835 Location Kimberly, Idaho, United States. 83341-5170 Starting Bid US $20,000 Bid Increment US $100...
  24. RanchWelder

    700R4 to 4L80E in my 87 Chevy Blazer

    Some people have posted that it is possble to swap out my 700R4 and install a 4L80E using the L29 or 0411 ECM? Own the L29. Will it work or not? The questions are: 1) Has anyone sucessfully used either ECM to control the transmission, without altering the OBD1? 2) Which ECM can be easily...
  25. RanchWelder

    1972 Chevrolet C10 - $12,500 (SHERIDAN, WYOMING)

    Looks cool. https://wyoming.craigslist.org/cto/d/sheridan-1972-chevrolet-c10/7636466412.html

Latest posts

Forum statistics

Threads
45,090
Posts
975,139
Members
38,038
Latest member
noonanstls
Top