Search results

  1. EvilGenius

    4wd indicator light wiring

    The light green, circuit 384, is the connection between the 4wd relay and the tcc lockup. I read about it here as well
  2. EvilGenius

    4wd indicator light wiring

    Yeah the white wire is continuous from the switch connector. I'm curious how this 4wd relay is used though. It is also tied into the tcc lockup so that when in 4wd, there is no lockup.
  3. EvilGenius

    4wd indicator light wiring

    Adding some info and bumping this post. Here is the harness in question. The plug at the right end is what plugs into the transfer case switch. The light around the center of the harness is the illumination light on the shifter mounted in the cab. The left side is what has me confused...
  4. EvilGenius

    4wd indicator light wiring

    Finally installing a lot of the wiring into my rebuild. When looking at the sub harness for the 4wd indicator light the white wire that runs from the tcase switch is cut. I'm not sure where it should go. I've dug through the wiring diagrams and it seems it should go to a 4wd indicator relay...
  5. EvilGenius

    Engine Mount Question

    The slotted holes are the factory mount holes. See my pic below. Usually engine mount adapters like the dirty dingos are used in conjunction with the original style motor mounts although it would seem like that company would have some installation pics as reference for you.
  6. EvilGenius

    700R4 Cooler Line Routing

    Well it looks like I have some rerouting in my future. Thanks for the photos!
  7. EvilGenius

    700R4 Cooler Line Routing

    Thanks for the pictures. Looks like you have a 2wd though. Not sure if that affects the routing.
  8. EvilGenius

    700R4 Cooler Line Routing

    Here is how my lines are routed. It was hard to capture in one photo, so I took it in stages. Picture 4 has where I am in contact with the headers.
  9. EvilGenius

    700R4 Cooler Line Routing

    I recently purchased and installed pre-bent cooler lines from Inline tube. They look great and seem like a quality product. Here is the issue though, I can't figure out how they should be run. I have them installed now, but they are tight up against the headers and that cannot be correct. Does...
  10. EvilGenius

    Wiper Pulse Module #15598496

    Nice find! With all the components labeled like that, you can just have new boards made and make a new one from scratch.
  11. EvilGenius

    Cab to Fender Seal?

    Now that I know that, I'll keep an eye out when I hit up the scrap yards. Also if I decide not to use them I'll post them up on here.
  12. EvilGenius

    Cab to Fender Seal?

    I was recently pulling parts off of my other cab and pulled off what appear to be a foam seal between the cab and the front fenders. Was this a factory option and are they necessary? I can't recall seeing them on any of the parts sites like LMC. Pic of it on the cab: Pic of one removed...
  13. EvilGenius

    Blue two tone trucks

    I'm also looking for an answer to this question as my paint selection is blue with a white stripe. I do however, have a source for new stripes. https://www.phoenixgraphix.com/gm/8491gmt5b.php Not sure which stripe color would look the best though.
  14. EvilGenius

    Kick Panel Speaker

    @eskimomann209 What seats are you running in this truck? I've seen the pictures in a couple other of your posts and I'm looking for something similar. Also, how did these kick panel pods turn out in your opinion?
  15. EvilGenius

    Bulkhead / Firewall Connector

    I would check out the scrap yards near you. This one that I somewhat frequent has at least 6 squares in it. They probably all have that connector sitting in them untouched. Depending on how soon you need it, I have an extra cab and engine harness. The issue is I'm not sure which of my two sets...
  16. EvilGenius

    Fuel Lines (Hard)

    Inline Tube also does similar stuff. I'm not sure how they compare on price. Inline Tube is based out of Michigan though, you could potentially save on shipping and pick it up yourself since you seem to be nearby somewhat.
  17. EvilGenius

    ISO Engine Bay Pics

    I'm looking for pictures of line routing in the engine bay. Fuel lines, tranny cooler lines, brake lines, and power steering lines. I don't seem to have many good pictures of how these lines are routed in the engine bay and would like some reference pictures as I reassemble. I'm cutting and...
  18. EvilGenius

    Looking for another work truck

    Hello. I own a 2018 LT Silverado 1500 with the 5.3. Overall they are great trucks. I personally have not had any problems. I frequent another forum for them and have read about some of the issues people have. I'll try to highlight some of my learnings from that. Keep in mind that most people go...
  19. EvilGenius

    Ryobi 1/2" impact

    I have a Ryobi impact and it's been great for what it is. I've beat on my mine for a couple years now and it's held up great. It does have some stuff it can't take off, but it's not real common.
  20. EvilGenius

    Body/Frame Swap...Talk Me Out of It

    In a way swapping frames is very similar to replacing a 4x4 truck's cab with a donor 4x2 truck's cab. That's the process I've been going through. It hasn't been hard or complicated. Moving the cab from one chassis to another was done with my engine hoist. It's practically a one man job although...
  21. EvilGenius

    Factory stripe kit.

    This website has many different colors of the stripe sets. They also have many new prints of engine bay graphics. https://www.phoenixgraphix.com/gm/8491gmt5b.php
  22. EvilGenius

    Bvllsh!t on craigslist.

    Pretty good deal on a C20 Crew Cab. https://detroit.craigslist.org/mcb/cto/d/roseville-1986-chevy-c20-4-door-pick-up/7005774605.html
  23. EvilGenius

    Impact wrenches

    I'm in a similar boat as the OP. I mostly use Ryobi because of their battery system and I already had some of their tools before I really started looking into specific tools. I actually have this cordless Ryobi impact and it works awesome. Out of all my tools this thing gets the most use...
  24. EvilGenius

    Rear Brake Line Hanger

    Looking for the brake line hanger that is riveted to the frame on the passenger side above the rear differential. Mine was removed via torch and was tossed at some point. Please see the picture below for reference (Source: google images)
  25. EvilGenius

    K10 front brake pads wrong thickness?

    Just to clear this up, the pads I had ended up working well. To correct the issue I was having, the inserts on the bolt eyes of the caliper have to be slid over so that they are flush with the inner surface of the bolt eyes. I was unaware that they could be moved when I first started doing the...

Latest posts

Forum statistics

Threads
45,501
Posts
984,707
Members
38,561
Latest member
ChadwickPNW
Top