Search results

  1. Josh Helm

    700r4 blown. Nv3500/4500 swap

    I have done the 3500 swap and love it ... minus needing to swap my ring gears now cause never use 5th under 80mph ... lol ...
  2. Josh Helm

    Suburban Build For Camping/Hunting/Fishing

    I'll second that
  3. Josh Helm

    CUCV M1028 Part out Mint Body

    Whatd you ger for um if you don't mind me asking
  4. Josh Helm

    CUCV M1028 Part out Mint Body

    So whats the price on the axle set? I interested .. anyone know are they high pinnion d60's on these?
  5. Josh Helm

    Sm465 not shifting

    Yes and no ... the ball yes should be able to snap back on .. but if it's popped off already it will unfortunately happen agian ... the spring retainer is probably lost it's luster... as for the throwout bearing i highly doubt it's bad.. being fresh and not many miles... so if I were you ... I...
  6. Josh Helm

    Sm465 not shifting

    Is it still hooked on the ball ?... maybe guy you had installed the clutch installed throwout bearing in correctly ... it pretty easy to do actually ... it'll slide into fork couple different ways .. but only one is correct!!
  7. Josh Helm

    Tach conversion kits

    Dakota digital ... one of the best money can by ... lifetime warranty... just my thoughts
  8. Josh Helm

    Sm465 not shifting

    Then it's in you hydraulic system ... your not getting enough throw ... ... check the slave and master for leaks you got air in it some where... you need it sealed and rebleed and you'll be rocking and rolling agian
  9. Josh Helm

    Question about backfire on throttle release

    Or depending on your timing light ... you can have a offset... rev it up to 2500 and ad just the offset till your at zero ... then look at the offset and it'll tell you your total timing ... I run mine at 35 ... cam heads and headers
  10. Josh Helm

    Sm465 not shifting

    I would deffently look at the hydraulic system ... trans and clutch should be fine ... dose it jurk if you try to start it in gear with clutch in?
  11. Josh Helm

    Frame info

    I am not aware of the changes in front leads but mine is a 82 that I restored ... lmc should mention if there a difference ... just as a reference guide
  12. Josh Helm

    Suburban Build For Camping/Hunting/Fishing

    Minus the cucvs... when do you get a good set of axles anyway?
  13. Josh Helm

    Question about backfire on throttle release

    What's your timing set at?
  14. Josh Helm

    Frame info

    Here's better look at um ... they look little arched here.. but keep in mind the frame is unloaded ... no engine and body ... and stock steering is maintained btw
  15. Josh Helm

    Frame info

    Plenty of room !
  16. Josh Helm

    Frame info

    2 inch lift springs will clear 33s ... but full crank offroading with flex may make contact ... I run 33 12.5 on factory ralleys and offroad and haven't hit once ... and the 2 inch lift springs will look flat .. but they do enough
  17. Josh Helm

    Opinion on "high mileage"

    Much agreeded on the surrounds when you by used... an other killer is sitting ... hasn't been mentioned yet... they die when they sit ... no oil in heads ... hoses dryrot ... injectors set up ... valve train isn't rotated... etc... to me sitting is worse then high mileage in some cases
  18. Josh Helm

    Opinion on "high mileage"

    Well it all comes down to maintenance... I have a tacoma that frame shit out round 350k ... still runs great no ticks dosnet leak or burn a drop of oil ... and I have seen machines with less the 50 k and are shot... specially when people don't change oil ... you can kill um fast ... or make um...
  19. Josh Helm

    Guess The Tool

    Bearing race remover ... for taking races of shafts or spindles
  20. Josh Helm

    Guess The Tool

    Yep I have done that ... but without the slide hammer lol
  21. Josh Helm

    Guess The Tool

    Cheating ... guess I should did better lol
  22. Josh Helm

    New door panel and dash, best quality?

    Omg is what I purchased as well ... although I would ad a a few from back side of armrest towards the dash ... we're there is a alignment pin ... they tend to work there way up over time ... their dash pad was good for fitment ... but quality wasn't the best ... scratched super easy... and I...
  23. Josh Helm

    Guess The Tool

    Well I covered up viscometer that was labeled on the side ... just threw one up ... lol
  24. Josh Helm

    Help with cab corner fitment

    I'll second the pie cut ... mine weren't to bad ... but thats where getting best panels you can get to start helps but... there s always mods to do
  25. Josh Helm

    Guess The Tool

    I could get you guys with countless eltrical testing equipment ... but it's not interesting in explaining there tasks ... lol

Latest posts

Forum statistics

Threads
45,477
Posts
984,208
Members
38,526
Latest member
Tdabney
Top