Search results
-
Another Newbie
welcome from down the street Belleview Florida we are all here to help . post up some pics so we can see what you have to start with and tell us what you have planed to do- 74propu
- Post #2
- Forum: Introduction
-
visor worth anything?
check and see what shipping to 34420 would be ???? -
Opinions on my rust issue
I put floor pans and rockers in both my trucks with a little 115 volt wire welder with flux core wire- 74propu
- Post #4
- Forum: Paint and Body
-
-
Bvllsh!t on craigslist.
if the fart box thing don't work try the pop sickle thing . during a night :humitp: put a pop sickle in your mouth and when your tongue gets good and cold lick the little man in the boat and when she gets off the ceiling she will do one of 2 things she will give you anything you want for (1 to...- 74propu
- Post #16,406
- Forum: eBay & Craiglist Listings
-
Frigette a/c info
that is a dealer add on air system . I put one in my 74 c10 and had one in my dads 75 c10 they work very good . nostalgicac.com has a unit they sale that is like ours they have all parts you will need to make it work again these ac systems came with York compressors back in the day I have put a... -
aztec cooling fans in a 86 square
the string was used for pulley alignment and belt size- 74propu
- Post #4
- Forum: Engine & Performance
-
aztec cooling fans in a 86 square
well I made a mounting adaptor to mount a Aztec hd cooling fans and shroud on my heavy duty diesel radiator made out of 18gauge sheet metal cut the top and bottom to 32in and bent to L brackets on the picnic table with a 2x4 clamped to it then cut the sides to 15 in and bent to L brackets...- 74propu
- Thread
- Replies: 3
- Forum: Engine & Performance
-
A/C later model controls
what you are talking about is a dealer add on air . it sits under the dash above the heater box with the controls where the ac vent is in a factory ac truck they are hard to find I looked for 2 years for the one I have in my 74 .so don't trash it when you take it out .behind the glove box you... -
Turn signal blinkers not working
oh oh oh I know this one the led bulbs don't draw enough power to make the flasher work there is a little led resistor that you need to wire in with the rear bulbs to make them work you can get the resistors from Walmart put them in then all will work as it should- 74propu
- Post #5
- Forum: Electrical & Audio
-
New Guy in CA soon to be FL
welcome from Florida the land of no smog or st inspection:cheers: where in Fl are you moving??- 74propu
- Post #2
- Forum: Introduction
-
fuel cell with or without foam?
i have a 15 gal fuel cell without foam in my 74 with a sender in it with the foam the gauge sender will not work the foam will keep the float in the full or empty point will not rise and lower with the fuel my gauge dose not bounce around at all till it is below 1/4 tank I got it off ebay I...- 74propu
- Post #3
- Forum: Tech Discussion
-
oil presser gauge wire
found it today it was tan the blue wire is for the chock presser switch. thanks for the help:cheers:- 74propu
- Post #5
- Forum: Tech Discussion
-
oil presser gauge wire
I cant find the oil presser gauge wire in my 86 c10 .it has been cut off and I cant find it in the wire harness under the hood . can ant one tell me what color the wire should be ???? thanks- 74propu
- Thread
- Replies: 5
- Forum: Tech Discussion
-
Engine Accessories
or the strap is there because the po striped out the alt where the top bolt will not tighten up and hold the alt belt tight . try and tighten the top adjustment bolt in the bracket if it is striped you can just get a longer bolt and put a nut on it on the back side of the alt the take off the...- 74propu
- Post #14
- Forum: Tech Discussion
-
What have you done to your square lately??
installed headers on the phantom dually -
Affordable engine replacement?
a few years a go I bought a 350 from a local machine shop that had not been picked up when they were done with the rebuild. it was 30 over new pistons new cam vortec heads hi presser oil pump all the good chit thay just wanted there money back out of it I gave around $600 for it stuck it in my...- 74propu
- Post #9
- Forum: Engine & Performance
-
cummins swap brake options???
my 1986 dodge 3500 cummins has vacuum boosted brakes on it that is run by the vacuum pump . that is the factory setup on dodge diesels- 74propu
- Post #3
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
Square on the Interstate
my 74 don't start running good till around 80 and likes 100 as a cruse speed that's when it is happy about 4 pounds of boost so go for it- 74propu
- Post #12
- Forum: Engine & Performance
-
New member
welcome nice truck I would kill for that topper :gr_guns:- 74propu
- Post #2
- Forum: Introduction
-
Stereo install complete with speakers in doors with power windows
more money more money and still more money but momma has it I hope ( I make it and she takes it and tells me we are broke ho's that I need to work a street corner and make some $$$$ )- 74propu
- Post #36
- Forum: Stereo & Entertainment Systems
-
Stereo install complete with speakers in doors with power windows
well thanks there home town . now I have to re think all my speaker install in the phantom dually was going to put them in the dash and in the cab corners . so thank you very much :bawl:- 74propu
- Post #34
- Forum: Stereo & Entertainment Systems
-
What have you done to your square lately??
been welding in floor pans and rockers on the 86 when my flux core welder took a dump so mama found a Lincoln sp100 mig welder with argon bottle for sale on craigslist went and looked at it the bottle is almost full and I dam near ripped my pocket right off my jeans getting out the $300 he... -
Looking at an RV 454 Friday...
Adam where are you going to look at this 454 & trans there is one for sale here where I live in belleview . the flex plates do crack and make one hella sound and look at the trans real good some motor homes came with a gear vender o/d hanging on the end of the trans . if it dose have the o/d...- 74propu
- Post #4
- Forum: Engine & Performance
-
Front Bed Panel Removal
I have the same problem with the bed on my 86 . I am going to weld a pull tab on it right where the bend is then put a chain on the rear bumper that I can hook a come a long on then hook the other end of the come along to the pull tab then tighten the come along and tap the bed wall with a...- 74propu
- Post #3
- Forum: Paint and Body
