Search results

  1. C10MixMaster

    Water Temp Sensor

    in my opinion the head will give faster more accurate readings than the manifold. however if the manifold is the only place you place it fits it should be close enough to work.
  2. C10MixMaster

    Front Wheel Bearings

    I would never replace a bearing without doing the race to. might have to pull the race and cross reference the number .
  3. C10MixMaster

    Slip yoke leak

    there's an oring inside the end of the tube that's where the leak is. Easy fix , probably easer that trying to JB weld it.
  4. C10MixMaster

    Bed Carriage bolt holes

    Stepside bed washers could be another option
  5. C10MixMaster

    Which welder?

    ok I meant I haven't seen it bird nest or had the spool running loose which would be the most likely cause of the wire getting wrapped under itself. I have not noticed if the wire wasn't spooled correctly from the manufacture, but next time I have a problem I will look there to.
  6. C10MixMaster

    Which welder?

    the best I can tell, I haven't seen it bird nesting.
  7. C10MixMaster

    Which welder?

    Tanks for the advice, I am defiantly a novice welder. With this welder I have replaced the ground clamp the original was sheet metal and not very reliable now it has a heavy brass clamp. Replaced the gas pressure regulator the original leaked from day 1 causing inconsistent gas flow, it now...
  8. C10MixMaster

    Which welder?

    I have a Hobart 135 110v Mig . From what I can tell Miller owns Hobart, I believe on the lower end machines they are probably the same just paying a little more for miller name. My experience is that my Hobart occasionally has wire feed issues, never really pinned down as to why but it...
  9. C10MixMaster

    Fusible Links vs Maxi Fuse

    OK when I was working on European cars I never saw a fusible link and I cant think of any modern American car that uses them, they all use fuses now to the best of my knowledge. The OE configuration on my 77 going by wiring diagrams, there are 2 fusible links between the Alt charge wire and...
  10. C10MixMaster

    What have you done to your square lately??

    I did this once and the Dr fished it out with a magnet actually worker pretty good
  11. C10MixMaster

    What have you done to your square lately??

    ran the final pattern on the gears and put the diff back in the truck
  12. C10MixMaster

    Fuel supply issue

    You should be looking at the fuel pump. in warm weather the carb going dry is common. A good fuel pump should resupply the carb and start after the engine turns over a couple time.
  13. C10MixMaster

    Truetrac question

    that's what I was hoping to hear . :cheers:
  14. C10MixMaster

    Tuning for altitude

    Yes that's 13.4 parts air to 1 part fuel.. Theoretical ideal is 14.7:1 , Richer to a point will produce more power and leaner to a point will get better mileage.
  15. C10MixMaster

    Truetrac question

    well talked to Eaton and verified the holes are to there spec. I guess were going to find out if the clamping force of the bolts is sufficient. I haven't heard of any problems from the ring gears coming loose.
  16. C10MixMaster

    What have you done to your square lately??

    corvette atomic orange
  17. C10MixMaster

    What have you done to your square lately??

    Finally started the install on the Posi , got the old carrier out
  18. C10MixMaster

    Timing on GM GoodWrench Crate Engine?

    harmonic balancers , timing covers/timing tabs interchange between motors pretty easy. In your case someone is going to have to verify TDC by the piston and then you can figure out if you have a 12 o'clock balancer and tab or a 2 o'clock balancer and tab or if the balancer has slipped or they...
  19. C10MixMaster

    Fusible Links vs Maxi Fuse

    I would base fuses on the wiring they are protecting not what they are powering.
  20. C10MixMaster

    Fusible Links vs Maxi Fuse

    I rewired mine using fusible links but in retrospect I wish I would have done maxi fuses. I've never been a fan of fusible links..
  21. C10MixMaster

    Truetrac question

    I was doing a preassembly on the truetrac that should be going into the truck soon. One thing i noticed is the bolt holes in the carrier are larger than the bolts. the bolt holes measure 13/32 and the bolts are 3/8. so there is 1/32 or .030 inches of slop , seams excusive for something that...
  22. C10MixMaster

    Tuning for altitude

    Temperature defiantly makes a difference. I got a WB wideband air fuel ratio gauge , was planning on using it to tune and then remove it. I also have an APT Adjustable part throttle this allows me to adjust the cruise mixture . What I found is if I set the cruise mixture at 14.7 : 1 in the...
  23. C10MixMaster

    Tuning for altitude

    cam profile or a larger nozzle
  24. C10MixMaster

    Part Number for Front Tank Bracket - Passenger Side

    I would weld or find a friend who could weld nuts in the collect location :33:.
  25. C10MixMaster

    Tuning for altitude

    check the accelerator pump, there should be zero slop in the linkage and it should squirt at soon as you move the throttle.

Latest posts

Forum statistics

Threads
45,454
Posts
983,809
Members
38,502
Latest member
GorillaHumper
Top