Search results

  1. sickchev

    1990 suburban cluster

    What you want for it @Strick
  2. sickchev

    1990 suburban cluster

    Im looking for a 1990-1991suburban dash cluster. Im hoping to find one with a tachometer but if not thats okay. Im looking for a electronic speedo version.
  3. sickchev

    What have you done to your square lately??

    Used the 81 gmc 1500 to harvest melons!
  4. sickchev

    tilt steering column

    There are 4 reverse t8 blots that need tighted down and it will take the slop out.
  5. sickchev

    Does anyone make 17" aluminum 4x4 Rally wheels?

    Wheel Vintiques
  6. sickchev

    Painting rally wheel rim

    Eastwood 2k wheel primer. Comes in a rattle can. Then top coat it with whatever you want. I would go for the Eastwood 2k rattle can areospray top coat.
  7. sickchev

    Removing engine and trans.

    Yeah I guess I forgot to mention I usually keep a variety of old yokes around that I stick back in the trans after I drop the shafts out.
  8. sickchev

    Removing engine and trans.

    It wasn't me that posted it but I can try to help you out. I usually start at the back and work my way forward. I'll give you the main points I can remember and it should get you close. 1. Disconnect drive shaft - tape up u-joints 2. Unbolt the trans from the cross member 3.Disconnect trans...
  9. sickchev

    Help with GM 14 Bolt Rear End

    80W90 is fine to run
  10. sickchev

    Help with GM 14 Bolt Rear End

    My best guess would be wrong torque when it was put in at some point. Too much torque cracked the prong and the bolt backed out with nothing to hold on.
  11. sickchev

    Help with GM 14 Bolt Rear End

    GM 14 Bolt Side Adjuster Lock Prong http://www.billavista.com/tech/Articles/14-Bolt_Gear_Setup/index.html
  12. sickchev

    Turn Signal Power

    I am looking for some turn signal help. I have tried the usual suspects but I'm a little confused about this one. 1977 C30 Automatic Tested 12s volt on both sides of the glass fuse - Good Tested 12 volts at the flasher (552 Round Style) - Good Tested 12 volts up to the switch on the purple wire...
  13. sickchev

    8.1 Vortec VS 383 Stroker VS 6.0 Iron LS

    My advice on a ls swap is buy a whole 1999-2002 silverado/suburban 2500 6.0 that runs. Drive by cable (99-02) is simpler IMO. Don't sell anything off the donor until the job is finished. You would be amazed at how frustrating and expensive it will be if you have to buy everything separate. It...
  14. sickchev

    Nv3500 to older sbc

    How did you handle the clutch master cylinder install?
  15. sickchev

    AC delete panel

    I found this video a few years ago when I was debating ac delete or vintage air. I hope it helps
  16. sickchev

    For you LS swap guys.

    Here is my view and how I handle my 5.3 swaps. I purchased a 5.3 lm7 2001 from a awesome guy that pulls from a yard. He has them on a stand and you can hear then run. This did at least make me feel better that it would run so I pulled the trigger. It's was a 200k+ motor but I went into the...
  17. sickchev

    305 SBC vs 6.2 Detroit: Which would you rather?

    My vote is for the 305. I know they make poor power but they live forever. Most 305 have not been abused like a 350 because people don't use them in projects where they want to make big power. You can get them or parts dirt cheap, sometimes even free from marketplace. Most 350 parts will bolt on...
  18. sickchev

    Single din install problem

    Before I'd hack the dash out I would buy a 2 knob Bluetooth unit. It weights nothing and just mounts using the knob holes. Fm/Bluetooth to the phone.
  19. sickchev

    Anyone know to install

    While I would advocate for the mechanical like mentioned earlier. Here is the instruction guide for one of these style pumps if you are firm set on running one. This paper I assume would be in your packaging also.
  20. sickchev

    Anyone know to install

    Hey man, if your small block has a mechanical pump you don't need a electric one. The mechanical ones will last forever. Why did you block off and switch?
  21. sickchev

    Underside of hood coating ideas?

    Just my opinion but the rubberized coating is extremely hard to get back off. I used these 2k products from eastwood. They are ceramic based 2 part so its tough as nails. https://www.eastwood.com/ew-2k-ceramic-aerosol-underhood-black.html
  22. sickchev

    Rear Main Seal

    They sell uv die you can add to oil. Get a black light and find the true source of the leak. There are multiple sources that could cause a bad leak.
  23. sickchev

    Rear Main Seal

    Did you remember your gasket on the distributor?
  24. sickchev

    Preferred Solder for Automotive Wiring

    I really like the Solder Seal butt connectors. They soder the wire and heat shrink all at once. I have pulled hard as hell testing them and they dont let go. https://a.co/d/0CyEoBH
  25. sickchev

    Looking for a sleeper

    https://www.facebook.com/marketplace/item/234327509529936/?mibextid=dXMIcH here is one I found in ohio

Latest posts

Forum statistics

Threads
44,756
Posts
967,433
Members
37,484
Latest member
weedoz
Top