Search results

  1. gpmorgan

    TH400 Suggestions?

    www.summitracing.com/parts/hu This is what I used behind a 632ci big block.
  2. gpmorgan

    O2 Sensor

    I bought a collector with the bung in it.
  3. gpmorgan

    What Ls engine should I go with

    I've got a couple of short vids when I got it running but can't get them to load on here. My son has been trying to get me to make some and put them on ytube. Mabe soon I'll have a few.
  4. gpmorgan

    What Ls engine should I go with

    I'm very pleased with it. Runs great. I'm looking to get some dot street radials soon. I think I'm going to try the m&h tire.
  5. gpmorgan

    What Ls engine should I go with

    BPE 632
  6. gpmorgan

    Wiper/ turn signal switch

    Sounds like signs of bad switch or switch is out of adjustment.
  7. gpmorgan

    Wiper/ turn signal switch

    Your high/low beam switch is mounted on the collum under the dash. You may have a bad wiper motor possibly.
  8. gpmorgan

    SBC 350 with new cam will not start, only pops a couple times then nothing.

    You need to get number one cyl up on the compression stroke and see which terminal the rotor is pointing to on the cap. You can make number one where ever it is pointing. Bump my last post. I reread your post and you have your cam and crank gears correct.
  9. gpmorgan

    SBC 350 with new cam will not start, only pops a couple times then nothing.

    Your timing chain gears should be dot to dot also.
  10. gpmorgan

    550HP and tire melting?

    Yeah. And not that cheap stuff.
  11. gpmorgan

    550HP and tire melting?

    The words "stone stock" are never in a hot rodders vocabulary. Lol.
  12. gpmorgan

    550HP and tire melting?

    I have a fitech on a bbc. It didn't help with the "two words". It has killer throttle responce though.
  13. gpmorgan

    550HP and tire melting?

    The two words "fuel mileage" are never in a hot rodders vocabulary. Lol.
  14. gpmorgan

    Gilmer Belt Kit

    I found some. Yeah I like that belt too.
  15. gpmorgan

    Gilmer Belt Kit

    My bad. Your are right. What's a Gilmer belt?
  16. gpmorgan

    Gilmer Belt Kit

    I was referring to the last paragraph of his post.
  17. gpmorgan

    Gilmer Belt Kit

    This is one of their sets I installed on my engine.
  18. gpmorgan

    Gilmer Belt Kit

    ://www.summitracing.com/search/product-line/march-performance-chevy-small-block-serpentine-conversion-kits?SortBy=Default&SortOrder=Ascending&tw=March&sw=March%20Performance%20Chevy%20Small%20Block%20Serpenti they are pricey!!
  19. gpmorgan

    How to tell roller cam or not

    The roller or hyd roller cam has different lobe profiles to open and close the valves faster. The lifter has a roller where it contacts the cam lobe. I thought only the vortec engines got the roller setup. Not sure. You can check your engine id numbers and probably find out what it has.
  20. gpmorgan

    Best mud tire?

    I bought a set of mud claw blemished tires for my son's truck . 815 bucks. 35x16. They have a little over 20k miles and are about half gone. They work well in the mud and aren't very loud on the street. I would recommend them to anyone.
  21. gpmorgan

    The swap started today.....

    Summit has all types of yokes and conversion u-joints. I recently went from a 700r4 to a th400 and that's where I found what I needed.
  22. gpmorgan

    TBI rough on a warm or hot restart

    I had a similar problem with a 350 tbi. It was the fuel pump relay. Took it off and opened it up and found the contact tips burnt in the relay. Sanded and cleaned the contact tips and ran it for years. It would run ok but you had to spin the motor for several seconds before it would start.
  23. gpmorgan

    383 Stroker build

    With the 383, you will need to check for clearance of your rods on the block at the oil pan rails and bottom of the cylinder walls. Also a small base circle cam may be needed. Talk to your machinist about these issues. Check out some vids on stroker engine builds.
  24. gpmorgan

    is this normal?

    Yeah, you should need the cap and rotor only. I think the cap will come with the carbon plunger, spring, and insulator that goes between the coil and cap.
  25. gpmorgan

    New driveline choice

    If they don't want to move over, I usually smoke the tires and go sideways. That tends to work. Lol

Latest posts

Forum statistics

Threads
44,633
Posts
963,270
Members
37,199
Latest member
Bowtie-dad
Top