Search results

  1. gpmorgan

    carb suggestions for a 350

    For a stock or slightly modified 350, I would use the q-jet style carb. For a highly modified 350 I would use a Holley. Here's what I use on mine. http://www.holley.com/VirtualShow/chevy/silverado/2607.asp
  2. gpmorgan

    Few Questions for a possible future project

    Yes, acording to the pics, you have a th400.
  3. gpmorgan

    Talk me into or out of TBI

    If it's a stock motor I'd probably go with the TBI if I had all the parts for it. Otherwise I'd stay with the carb.
  4. gpmorgan

    Few Questions for a possible future project

    https://www.google.com/search?q=gm+transmission+identity&rlz=1C1KMZB_enUS550US550&espv=210&es_sm=93&tbm=isch&tbo=u&source=univ&sa=X&ei=yi_TUq-_Csu4kQf3qYC4DQ&ved=0CDUQsAQ&biw=1241&bih=606
  5. gpmorgan

    Hood questions

    The reason the hood bent is probably because the hinges have not been lubed in quite some time. Sounds like you may need a hood.
  6. gpmorgan

    Freeze plug

    I've never had a 3.4. I was just saying I've had had some rider that were piles.lol
  7. gpmorgan

    Freeze plug

    Yeah, I've had a few of those.
  8. gpmorgan

    Freeze plug

    Was that an aluminum block, Retro?
  9. gpmorgan

    Freeze plug

    I put one like in the pic, except I think it was brass, in a 72 big block. Ran it for 5 or 6 yrs and sold it. So I'll say they work pretty good.
  10. gpmorgan

    Fuse keeps blowing causing no lights

    I would lean toward the turn signal switch in the column being bad.
  11. gpmorgan

    700R4 Lockup adjustment?

    http://www.sonnax.com/parts/2513 Check this link out. This could be causing your problem. I have one of these valves in my 700r4 and it will stay in od at wide open throttle.
  12. gpmorgan

    700R4 Lockup adjustment?

    This is just a guess. It may be the 373 gear is fooling the ecu making it think it going faster than it is and keeping it from staying in OD. Im not sure and it may be controlled by the TPS. Welcome to the forum Mark.
  13. gpmorgan

    New Member from Texas - Baron

    Welcome Baron.
  14. gpmorgan

    1987 C10 5.7 TBI check engine light on.

    Welcome to the forum Brandon. Sorry, I didn't notice you are not a new menber.:suicide: Welcome anyway.:Big Laugh:
  15. gpmorgan

    1987 C10 5.7 TBI check engine light on.

    1. Ground terminals A and B (see diagram below) with the ignition "ON" and engine not running. The system will enter the diagnostic mode. In this mode, the computer will display a Code 12, three consecutive times, by flashing the "CHECK ENGINE", "SERVICE ENGINE SOON" or "MALFUNCTION INDICATOR...
  16. gpmorgan

    New Girl from WIsconsin

    Welcome to the forum Danni. I have a niece named Danielle. That's a great looking truck!!
  17. gpmorgan

    Torque Converter Suggestions? Turbo 350

    Since stall is determined by torque. It's hard to compare stall speeds on a big block and a small block. The same converter will stall more on a big block than a small block.
  18. gpmorgan

    Battery Conversion/Wiring

    Now that you mention the butt connector, I remember seeing them that way. They will work well but you need to use crimping pliers to crimp the connector.
  19. gpmorgan

    Battery Conversion/Wiring

    The positive cable should go straight to starter terminal from the battery. I'd check somewhere else for that negative cable with the extra ground. It should be available.
  20. gpmorgan

    Replace Axle Bearing and Seal

    Here is a you tube vid on axle bearing replacement. It's on a Ford c-clip diff and will be the same method on your c-clip diff. http://www.youtube.com/watch?v=Tr9JXP6w1ko
  21. gpmorgan

    Replace Axle Bearing and Seal

    Once you get the axle out you should be able to see the bearing. There is only one bearing. The inner bearing is on the carrier and should not need to be replaced. You do have a C-clip diff right?? I think I would look at replacing the brake liners on that side if they were oil soaked.
  22. gpmorgan

    94ish Mud Race Chevy

    Did you guts do an axle swap on the front or is it a square body frame? That's a good looking Ford your pulling it with.
  23. gpmorgan

    4.3 v-6:

    A lot of manifolds are cast but that one looks likes steel because the tubes are welded together. If that's the case just have the tube cut and the hole welded up.
  24. gpmorgan

    Replace Axle Bearing and Seal

    Does the axle have any horizonal or verticle movement in it? That would indicate a bad bearing for sure. Did any of the gear oil get on the brakes? You should be able to remove the bearing with a slide hammer. If you don't have one you can do the loan a tool program at most parts stores.
  25. gpmorgan

    Torque Converter Suggestions? Turbo 350

    According to Comp Cams site that cam will work well with a 2000 plus converter. I have a comp magnum cam with 525 lift and I use a 12 in. 2500 stall. It could stand to have a little bigger stall but it works pretty well. I think if I were you I would use the 2500. I have a 700r4 trans with a 410...

Latest posts

Forum statistics

Threads
44,634
Posts
963,421
Members
37,209
Latest member
danrw2008
Top