Search results

  1. henrym

    Digital Dash

    Loving my Intellitronix Dash!!
  2. henrym

    new / interior in proress

    beautiful job, great attention to detail.
  3. henrym

    Rough running, then no start after head gasket swap

    check for a grounded/melted wire, since this didn't happen until it got to operating temp (hot). You may have a wire too close to the engine or exhaust, and a wire resting against it may have melted.
  4. henrym

    New Guage cluster

    I'm loving my Intellitronix digital gauges. Not hard to install at all, techline pretty helpful if you have any questions.
  5. henrym

    700r4 Rebuild advise

    Transgo and B&M make excellent kits, a reputable builder will know about upgrading sun/planetary gears, etc. A buddy of mine built up one for me with a Transgo kit, did some hard part up grades. The trans is a beast, having withstood towing (OD disabled), behind a SBC with a Holley...
  6. henrym

    Is 1.5* Positive Camber Too Much - If So, How Do I Adjust?

    These were meant to be in my previous pics/post. this was the setting after installing adjusters on the upper balljoints. . Plus my new Wranglers
  7. henrym

    High Hump Transmission Cover Fit Problem

    just go to the junk yard cut one out larger than the hole you cut in your truck, trim as needed, mark holes for bolts, seal with butyl tape, and bolt it down, piece of cake, structurally sound
  8. henrym

    Heat and soundproofing material

    I bought Fatmat off of ebay, much better price than Dyna mat, and half the cost
  9. henrym

    Complete 73-87 Wiring Diagrams

    thank you!! I was going blind trying to read the Chilton manual
  10. henrym

    Is 1.5* Positive Camber Too Much - If So, How Do I Adjust?

    Just remember that is magnified if larger tires are used, factory specs are for factory size tires. The amount of tire wear on my old BFG's showed it to be too excessive, causing the wear on the outer tire edges.
  11. henrym

    Audio unit and road noise

    have you considered the possibility of non-resistor type spark plugs being used? They are still sold, and an untrained parts guy/gal may have sold them. If it's time for a tune up, replace those plugs with resistor type. Most electrical issues become a process of elimination. good luck
  12. henrym

    Is 1.5* Positive Camber Too Much - If So, How Do I Adjust?

    just found out napa no longer supplied them, but here is a part number to take to O'reillys and they can cross over to their numbers 264-2064, or 264-2065, hope this helps
  13. henrym

    Need Help on brakes dragging badly.

    its very possible that the rod from the brake pedal may need to be shortened (by screwing in) because of slight manufacture build tolerances between the new vs old parts. All braking system are static, meaning they just sit there waiting to be used, by pressing the pedal. Aftermarket parts...
  14. henrym

    Is 1.5* Positive Camber Too Much - If So, How Do I Adjust?

    Napa sells camber kit for Dana 44 and 10 bolts, they come in varying degrees of adjustment, part numbers are 264-2062, 2642061,2642064,2642065, ranging from .5 degrees to 1.5 degrees. Unfortunately it may require 2 trips to the alignment rack to determine which one you may need, some shops may...
  15. henrym

    What is this sealer stuff?

    Napa sells tube of 3M seam sealer, just make sure you buy the interior version for use inside the truck or you'll suffer the horrid smell, which almost never goes away.
View older results

Latest posts

Forum statistics

Threads
44,567
Posts
961,184
Members
37,057
Latest member
Squarebuddy
Top