Search results
-
I guess I give up on the windows
I have to ask, have you ohmed the wire from switch to switch? Is there any chance that the contacts in the driver's door switch are the problem? I would put a meter across the driver's door switch contacts and measure that resistance and I would measure the voltage exactly the same way you... -
Whats you gas mileage on your squarebody truck?
A brand new KLR? I kind of hope it gets better than 41mpg. My DR 650 gets anywhere from 46 to 51 on paved roads. Somewhat less off-road depending on all of the obvious factors.- Redfish
- Post #231
- Forum: Tech Discussion
-
Hello from Central Louisiana
Welcome. I look forward to the Build Thread.- Redfish
- Post #6
- Forum: Introduction
-
Whats you gas mileage on your squarebody truck?
You are Very Welcome! I had a roughly 3 hour back road drive to and from Cruisin the Coast with The '87 very heavily loaded. I even had Mrs. Redfish/BigUn riding shotgun... According to the odometer which is now incorrect because I have 33 inch mud grips, I am getting 14ish mpg. That...- Redfish
- Post #227
- Forum: Tech Discussion
-
Sensor above oil filter 3 wire
Sorry, this one I don't know the answer to. I can speak with some authority about a 1987 because mine is relatively low mileage and is all original. 1987 had a single wire sending unit right above the oil filter and a two wire switch below the distributor. I am sure you and several other...- Redfish
- Post #4
- Forum: Tech Discussion
-
1987 R10 oil pressure switch location/leaking
I second @Ricko1966 on the tapered threads. The new sending unit will have a small amount of dry sealant painted on the threads. It's usually a dull red color. The sending unit has to ground through the engine, it is a single wire system. I did apply teflon tape to the threads on the...- Redfish
- Post #13
- Forum: Engine & Performance
-
1987 R10 oil pressure switch location/leaking
Regular right hand threads. I know for a fact because I have replaced the switch, the sending unit, and the knock sensor on my '87. The switch, located under the distributor is on a rather delicate brass piping assembly that can easily be broken off leaving the threaded part inside the motor...- Redfish
- Post #6
- Forum: Engine & Performance
-
1987 R10 oil pressure switch location/leaking
Sorry, wrong answers all around. Except for the knock sensor. It is indeed on the block on the passenger's side. The sending unit near the oil filter is for the oil pressure gauge. It will have a single wire attached. The switch under the distributor is a backup to the fuel pump relay...- Redfish
- Post #4
- Forum: Engine & Performance
-
Tuff Country Lift Kit Experience
Friend, if it's posted on this forum it is Public Domain. The pics are posted to help folks. If you are using them for that purpose, that makes me very happy.- Redfish
- Post #25
- Forum: Lifted & Off-Road Systems
-
'87 V1500 2" Lift Advice
I did not. I can tell you that I went from a very noticeable squat to a very slight rake. I put a level on it both on the bed rails and on the pinch welds under the cab and it is slightly nose down. The shocks are okay. They made it better and more controllable than the old and worn out...- Redfish
- Post #62
- Forum: Lifted & Off-Road Systems
-
Cruisin the Coast ‘23 - show pics added!
You saw that red 4 door Ford? My brother-in-law loved that one! Did you notice the tires on it? Those old mudgrips probably were not really safe to drive on anymore. I am happy with The Truck but I want it to be better. Driving it through the tightly packed venues it got a lot of attention... -
Cruisin the Coast ‘23 - show pics added!
Since you saw The Truck in person you can tell it looks better in pics than In Real Life. From a few feet away it's not too bad. I like The Truck a lot and it was completely reliable the entire time, including the 3 hour trip there and then 3 hours back home. I hope to make some serious... -
Cruisin the Coast ‘23 - show pics added!
Not exactly my style but this dually was very well done. I heard the owner fire it up so I walked over to get a pic of the engine bay for y'all. -
Cruisin the Coast ‘23 - show pics added!
Yes, I know it's a Ford but I have a soft spot for '78/'79 Fords. This one was clean and I LOVED the front bumper/winch setup. -
'87 V1500 2" Lift Advice
You might try calling Skyjacker directly. I actually spoke to a real person who actually knew what I had and what I was trying to do. You may not be as fortunate...- Redfish
- Post #58
- Forum: Lifted & Off-Road Systems
-
'87 V1500 2" Lift Advice
First, the blocks were already installed on the factory rear springs when I bought The Truck. There was a 3rd leaf added to the front and there was nothing about that set up that I liked. This is what that looked like: If, IF the blocks were not already there I may have considered springs...- Redfish
- Post #57
- Forum: Lifted & Off-Road Systems
-
Cruisin the Coast ‘23 - show pics added!
Well, I survived and so did The Truck. I have been running wide open for over a week, just got home this evening. Have to go to work in the morning and I really need another day to recover. I have a LOT of pics on my phone but for now I am just going to post some teaser photos. At the... -
Cruisin the Coast ‘23 - show pics added!
Loaded up... Mrs. Redfish is killing me and The Truck. -
What have you done to your square lately??
My Poor Old Truck! Mrs. Redfish doesn't understand that there are limits to the space in the bed of The '87. About to leave for Cruisin...
