Search results

  1. N

    Two tone paint

    Sorry to revive an old thread but does anyone have the measurement for the top two tone line on the 81 to 87 trucks, I understand they go just under door handle but a more presice measurement as a starting point would realy help me out. Thanks
  2. N

    Turn signal switch issues

    OK thanks, I'll check all that out
  3. N

    Turn signal switch issues

    Pulled wiring harness from a donor truck has a holley sniper and dakota digital gauges all that is working fine
  4. N

    Turn signal switch issues

    Looking for any insight before i rip column apart and put new turn signal switch in. So when the key is off but the headlight switch is on if you push the turn signal switch to activate the right side signals it powers up the truck like you had turned the key on but as soon as you push the...
  5. N

    Front inner bucket seat bracket

    Hello, just curious if anyone has the dimensions of the front inner bucket seat bracket that is welded to the floor. I have a set of factory buckets to install but just don't have that inner bracket and need to make them. Thanks
  6. N

    2wd vs 4wd shift linkage

    That was my first thought and when I switched that adjustment clevis it wouldn't go in the hole squarly so i was worried it would bind and make it hard to shift because the geometry was off
  7. N

    2wd vs 4wd shift linkage

    Is there any difference between the column to transmission shift linkage in a 2wd to 4wd. I pulled a steering column and linkage from a 2wd parts truck and installed it in a 4wd and the adjustment knob that holds the rod from the steering column hits the rear shackle and wont allow you to shift...
  8. N

    Mystery Bracket Under Dash

    I believe it is for the cruise control switch that holds the pedal in place once you set cruise
  9. N

    Vent window latch issues

    OK thanks, that's what I thought. This what the truck came with other than the one new vent window so must have been changed at some point
  10. N

    Vent window latch issues

    Hello, so I am rebuilding a 1979 k10 pickup. I cleaned up and repainted the frames on vent windows and new 2 piece rubber from precision as well as one new glass as I had one tinted and one non tinted. So put the windows all back together but now the latch on the new glass won't reach the frame...
  11. N

    Update to my 86 K10 Silverado Shortbed Stepside

    What company is the wood bed kit from? I have Installed quite a few wood bed kits and never had a 2 inch gap.
  12. N

    How many coats of paint?

    The color your spraying and the tier of product will determine how many coats of base are needed. A really transparent color like some reds and yellows and a cheaper product line might take more costs of base to get proper coverage. Sealers and tintable sealers can help with this. 3 coats of...
  13. N

    2wd fuse panel in 4wd

    The 4x4 truck has no fuse panel so I have a 2wd parts truck that I took the whole wiring harness out of. They are both 79's but are glass fuses and not ATO style fuses. I think it should work, don't see any problems. Just gonna have to add the wires in for the 4x4 which won't be a big deal...
  14. N

    2wd fuse panel in 4wd

    Just curious if there was any difference from a 2wd fuse panel to a 4wd panel besides not having the the ground wire and the pink/ black wire that ran to the transfer case to light the 4wd indicator on the gauges. Both trucks are 79's.
  15. N

    New here, building a 82 K10

    Truck is now finished. Had to fight with the headers as they were leaking bad on the rear drivers side so ended up cutting the flanges and using remflex gaskets to get them to seal up. Glad to be done this one and ready to cruise around.
  16. N

    Usa 1 Industries Dash pads

    It's a risk sure but lots of parts are on backorder from lots of companies these days. I've never had good luck from LMC and the last urethane dash pad I tried was a horrendous fit so I figured I'd take my chances and pay the money for good quality stuff.
  17. N

    Usa 1 Industries Dash pads

    Thank you, that looks pretty awesome. I'm just ordering a whole interior kit and just wanted to see if I was making the right choice
  18. N

    Usa 1 Industries Dash pads

    Anyone who has a Usa1 industries dash pad, just curious on fit and finish? Anyone have pictures of the dash pad installed, not installed, or any information woild be great. Thanks
  19. N

    New here, building a 82 K10

    Materials on dash pad? I started out by filling all the cracks in the dash pad and smoothing it all out and then the guy doing the upholstery covered it in the same leather that he is using on the seat. He did a tuck and rolled seam around the gauge cluster hump which is quite thick and looks a...
  20. N

    New here, building a 82 K10

    So close to being done, just waiting on the seat from the upholstery. Recovered dash pad and Headliner installed. Added just some little steps and the trim rings on the wheels.
  21. N

    New here, building a 82 K10

    I would say better than LMC, they deal with Auto Metal Direct for sheet metal I believe, which of all after market suppliers for sheet metal I find the best. I have used AMD for years and have no complaints. I just got the AMD interior mouldings and first glance they look great so we will see...
  22. N

    New here, building a 82 K10

    Getting some sun after a quick drive to set the dakota digital guages up.
  23. N

    New here, building a 82 K10

    Coming to the final stages of this build. Just waiting on interior to be finished up. Ended up having the dash pad just recovered as I couldn't get a good fit with the aftermarket one. Getting the parts up here to Canada was the hardest part but I will say USA 1 Industries parts are top notch...
  24. N

    New here, building a 82 K10

    Was repainted at some point and basically everything peeled off to the bare metal. I didn't notice any factory paint so looks like they stripped it before they repainted it and just didn't do proper process in painting it or didn't wait proper times. Whatever they did made my life easier...
  25. N

    New here, building a 82 K10

    Yup must have been at some point. Didn't seem to affect too much for panel fitment. I smoothed it all back out, since it's not seen when the fenders on I didn't worry about making it perfect but it's at least back to proper shape and would really have to look to notice any damage was there.

Latest posts

Forum statistics

Threads
44,168
Posts
950,800
Members
36,284
Latest member
RogerioHR
Top