Search results
-
Dome lamp ground short circuit questions.
Exactly like that.- Terry Wilkerson
- Post #81
- Forum: Electrical & Audio
-
-
Dome lamp ground short circuit questions.
My 86 has a floor lamp below the ashtray. Several white wire come together at that lamp holder.- Terry Wilkerson
- Post #79
- Forum: Electrical & Audio
-
FNG with a 1981 C30 Dually
Good looking truck! Welcome from KC- Terry Wilkerson
- Post #2
- Forum: Introduction
-
-
Compression test
Another interesting thing this problem started all the sudden. I immediately knew something was wrong. Does this tell anything?- Terry Wilkerson
- Post #18
- Forum: Engine & Performance
-
Compression test
Wet test on 4 and 6. No change on compression. If I go with heads and problem does not go away I should be able to use the heads on a short block??- Terry Wilkerson
- Post #17
- Forum: Engine & Performance
-
Window Felt Replacement
Try silicone spray. One of the guys suggested it to me on my new seals and it helped alot.- Terry Wilkerson
- Post #30
- Forum: Interior
-
Compression test
I did the compression test this morning. I warmed the engine up first. On first attempt to start it lock up. I knew #3 had water in it before. I pulled #3 and water ran out. I mean a lot. It started after #3 was cleared. Readings are as follows. 1 - 150 3 - 135 water in this cyl. 5 - 155 7 -...- Terry Wilkerson
- Post #14
- Forum: Engine & Performance
-
I’m in love - here’s the truck I’m dating
You need to call or go online and get a LMC truck catalog. 800-562-8782. They will have a lot of stuff you'll need.- Terry Wilkerson
- Post #37
- Forum: Introduction
-
I’m in love - here’s the truck I’m dating
Welcome from KC.- Terry Wilkerson
- Post #19
- Forum: Introduction
-
-
-
-
Window motor
I found the same hole in the driver door when I removed the door panel. Even with the hole the guy didn't get the motor installed right. Just make a patch and pop rivet it in place. You can get the motor and regulator out without butchering the door.- Terry Wilkerson
- Post #9
- Forum: Interior
-
-
Hi guys new here have 1987 c-10
Welcome from KC Nice truck, I like the stance!- Terry Wilkerson
- Post #4
- Forum: Introduction
-
-
-
Compression test
I'm working on another project car. I'm getting close to posting picks of the other project on other cars. I'm saying it may be a couple days or so before the compression test.. I will post the results of the test.- Terry Wilkerson
- Post #13
- Forum: Engine & Performance
-
Compression test
Thank you to all. I feel confident about doing the test.- Terry Wilkerson
- Post #11
- Forum: Engine & Performance
-
Compression test
The truck is down on power and sounds funny. Also had a small amount of coolant come out of #3 while rolling it over by had while setting vslves.- Terry Wilkerson
- Post #5
- Forum: Engine & Performance
-
Compression test
So pull all plugs out then do a dry test. I wound think you would be running the possibility of drawing something into the cyl,s.- Terry Wilkerson
- Post #4
- Forum: Engine & Performance
-
Compression test
Will soon run compression test on my square. Plan on doing dry and wet test. Should I run the complete dry test on all 8 cyl. then the complete wet on all 8 cyl or run dry then wet test on each cylinder before moving on to the next cyl.- Terry Wilkerson
- Thread
- Replies: 20
- Forum: Engine & Performance
-
Proud New 1976 Square Body owner!
Welcome from KC:welcome:- Terry Wilkerson
- Post #21
- Forum: Introduction
