Search results
-
It’s official, I’m a nerd
Good for you! @Frankenchevy! I installed my own Enphase 7k solar system so all I need is the charging station once I do that I'll be going that route, Also.- hoagster
- Post #8
- Forum: Other Vehicles
-
What have you done to your square lately??
Have you figured out what front axle you have? There are some clues on the pumpkin and axle. I got parts from several different sites one being, https://www.dennysdriveshaft.com/ There are a host of others but you need to identify exactly what you have. I got my spindles off of Amazon and saved... -
What have you done to your square lately??
Sealed all the spots I could find that need it. Next up primer and a lot of sanding! -
Bed swap
My short bed 73 has one sleeve on the drivers side, 2nd position! So only one long bolt? Go figure? Might be the gas tank config? Mine always had 2 tanks, but the Drivers side was added, custom tank and the install was wierd a couple of the few bolts I had to cut during the strip down.- hoagster
- Post #23
- Forum: Tech Discussion
-
What have you done to your square lately??
Yes, I got it from Auto metal direct! And put it together very frustrating getting all the bolt holes lined up. -
What have you done to your square lately??
Thank you, for the follow up! The $4 can stuff is there to stop flash rust and it is stuck. moving on! -
What have you done to your square lately??
Oh and so I finally got back to the cab! still stripping. which begs a question to @Grit dog I'm ready to lay down some DTM primer from Tamco, but because of time I have layed a layer of rattle can rustolem everywhere I stripped it down to the metal. Any words of wisdom! -
What have you done to your square lately??
Me too, we as humans will never fix global warming! Sorry girl it's even beyond you in your life time, and one valcano away from a fix! -
Mutha trucking Vintage Air
It wouldn't fit between the frame rails low. But my truck is a 4wd yours is 2wd. Here's a pic to show you were mine will go, thats a holley upper mount. -
Mutha trucking Vintage Air
If it will fit down low you can find brackets everywhere cheap. I have a K-10 and I couldn't drop my engine in without removing the compressor. -
one piece or two piece vent windows?
With all the vents being re-built lately you guys are convincing me to go one with no wing vent- hoagster
- Post #17
- Forum: Glass & Mirrors
-
-
Mutha trucking Vintage Air
Would be a good idea, what did you find when you pulled the old ones? My dad like Certs, I found 2 rolls of them a old lighter and a couple of 22 shells when I tore mine down. -
What have you done to your square lately??
Looks like I need to push her outside and do some wash down. -
What have you done to your square lately??
@GXPWeasel @Poppy 87 Here's how I removed and reinstalled my bed. It may take a couple of tries to get center but once you do you can remove it by yourself. The last picture is important you need a gap so once you pull all your bolts slip a 2x4 or something between the frame and bed so you... -
What have you done to your square lately??
I will take some tomorrow, moving cows today. It's already set up just need to attach the chains. -
Mutha trucking Vintage Air
Watching this thread let us know how the install goes! I'm going that way also and curious! -
What have you done to your square lately??
I put some eye bolts in the 4 of the bed mount locations and used the engine hoist made it super easy to remove and re-install -
Crazy question
It's only 20 bolts and do able for cheap! Sorry I didn't read the whole post. The only reason to remove the bed bolts would be to give you access to the five bolts on each side and ten bolts along the bottom. Also to insert the front body panel. I think it can be done without removing the whole...- hoagster
- Post #24
- Forum: Paint and Body
-
!977 K10 Bedsides
Purchased new from Auto Metal Direct, and if you have to patient not every bolt hole lines up and just for the front panel there are 20 bolts. Is it hard no just time consuming and frustrating getting it lined up and square.- hoagster
- Post #11
- Forum: Paint and Body
-
Burnouts with a NP203 full time 4wd?
I did a four wheel burnout with my first square, it was a 73 not the one I'm working on it had a 396 in it. I promptly got pulled over and issued a hefty ticket. That was a long time ago while I was in H.S. which I graduated in 77. No need to do a burn out. Go dig some holes with it in the woods.- hoagster
- Post #12
- Forum: Transfer Case
-
What have you done to your square lately??
Repaired my old 40lb blaster, tested it out on one side of my passenger side door. Finished the down to the metal with my favorite tool. Cleaned it then rattle caned it. Still need to fix all the mirror mounting spots over the years. And blast the other side. -
Where do these wires go?
If you got this far, go do a lookup on a Massey 135 diesel tractor wiring diagram! My guess is Key on, and a relay which will allow the starter to function if all the safety measures are met.- hoagster
- Post #3
- Forum: Electrical & Audio
-
What new tools have you got lately?
New to me 2005 7hp 60 gallon Maxus Air compressor. Installed in the barn. Only a single stage have to be patient using the Blaster but it will work better than my old tired 1960's compressor. -
What have you done to your square lately??
It's going to be a daily driver, not a show truck. That said every nut and bolt has been removed and everything has been either rebuilt or replaced. Doing body work now to fix the minor rust on the cab. Not full resto, I'm guessing you'd call it a full resto mod?
