Search results

  1. hoagster

    How would transmission fluid end up pooling on the intake? TH350

    If its a th350, 400 its on the other side!
  2. hoagster

    How would transmission fluid end up pooling on the intake? TH350

    It would be on top of the transmission, might have a tube/rubber hose dangling off one side. It's raining cats and dogs here other wise I'd take a picture for you.
  3. hoagster

    How would transmission fluid end up pooling on the intake? TH350

    Here's my 2 cents, on my 94 burb and muddauber hornet had plugged the vent line on the transmission. And it would work fine everything was normal driving around and soon as I shut it down and parked it the pressure built up in the trans would push the ATF out of the fill tube. So I say get it...
  4. hoagster

    Help identifying

    BR3 - C10 1984-87 2.73 non-locking, You can thank @RetroC10Sport for the info he posted the whole list. Bit it's hard to find. https://www.gmsquarebody.com/forums/the-squarebody-reference-library.52/ Squarebody rear axle codes
  5. hoagster

    Tail light help !!!

    The ground can take all of the lights out, or if any of those 3 splices are grounded stuff will not work. Make sure all of your bulbs are good! The housings for the lamps are good. It's only 4 wires fix it.
  6. hoagster

    Tail light help !!!

    Here is the wiring diagram for the Rear lights. This may help you understand why the all the wires look the same at the end.
  7. hoagster

    Muncie Swap Botch Job Manual Clutch

    Don't know, haven't started it yet still in the rebuild stage. The Muffler shop that built the system is the best one in the area. We'll see, there is a lot of stuff going on in that area. to get he shift linkage correct
  8. hoagster

    Muncie Swap Botch Job Manual Clutch

    You are correct, the small one keeps everything connected. and allows you to make adjustments.
  9. hoagster

    Muncie Swap Botch Job Manual Clutch

    @AuroraGirl I don't need a replacement, I was talking about the push rod from the pedal to the z bar. The two lower springs one holds the pivot pin to the clutch fork and the other pulls and holds the clutch fork away from the clutch when your not shifting. There should be two one small one and...
  10. hoagster

    Muncie Swap Botch Job Manual Clutch

    Original equipment. I purchased a new one because as you can see in the picture I repositioned one of the arms to accommodate the exhaust manifold change due to a LS swap. Next thing to do is build a new linkage rod to fix the slop in years of use. The old linkage from z bar to pedal is worn...
  11. hoagster

    Muncie Swap Botch Job Manual Clutch

    Here's a more recent picture.
  12. hoagster

    Muncie Swap Botch Job Manual Clutch

    Yoou can get parts from here! https://www.4speedconversions.com/73-87_truck_parts.html Although mine is not connected all the way because the cab is still off here are some pictures that might help. Plus mine has a sm465. There are suppossed to have felt on both ends also that keeps the grease...
  13. hoagster

    Cab Underside Treatment

    You and @Grit dog have seen the bottom of my cab. That is Tamco DTA primer. Like I said in your other thread I have never spray color and clear. If I screw it up I will cover it with an yet to be determined under coating. Probably 3m.
  14. hoagster

    Cab Mount Bolts/Captured Nut Loose

    Mine is laying on its back on a pallet, just do it gently. I'm a big guy and can do it by myself but get a friend. I usually have it on 6x6's on the rockers. If your cab corners are rusty though you'll need more help. I'm getting ready to shoot another coat of primer on the bottom. The color and...
  15. hoagster

    Cab Mount Bolts/Captured Nut Loose

    If your hump is removable I would take it off to so you can access the transfer case shifter also.
  16. hoagster

    Cab Mount Bolts/Captured Nut Loose

    yea it took me a couple of tries the first time. That cap locks on to the those crush pins on either side.
  17. hoagster

    2wd SM465 Speedo Gear Problems

    I don't know how my name got in the transmission thread for gear oil. I don't even have a thread saved for crc gear oil.
  18. hoagster

    Cab Mount Bolts/Captured Nut Loose

    Push it down and twist, it will pull right out!
  19. hoagster

    What have you done to your square lately??

    I still have my 350 long block 73 with all the brackets sitting in the barn! Thinking one day I tear it apart, but why?
  20. hoagster

    What have you done to your square lately??

    I think they should! On the truck side, no need to share the other!
  21. hoagster

    Hi From Melbourne Australia

    Very nice looking ride! Welcome from NorCal
  22. hoagster

    Front Sway Bar Brackets

    Here's an image of mine. Its a 73 K10, you know that already If I remember right had the frame on jack stands to get it all lined up, that way I could finagle everything. And the shocks were last.
  23. hoagster

    Don’t think this is normal☹️

    I'd be careful of sandblasting with all the open port and hoses! That stuff gets everywhere doesn't matter how careful you are!!!
  24. hoagster

    Don’t think this is normal☹️

    When you get that motor out if you are pulling it, Check all around the four bolts holding the freshly painted power steering unit. especially if the truck had non stock larger tires on it! This is what mine looked like!
  25. hoagster

    Rear Diff Leak

    So do everything in the previous posts but use this Diff cover gasket. No rtv and its reusable! It comes in all sizes 10, 12 and 14 bolt

Latest posts

Forum statistics

Threads
44,169
Posts
950,808
Members
36,286
Latest member
goodwrenchca
Top