Search results

  1. legozombie

    Engine Stalling - Bad EVAP/Charcoal Canister?

    I tried doing some research and didn't find anything relevant so here is a new thread. There is a question at the end, I am just trying to give as much back story as I can. Without further adieu... So last week I was changing out the fuel sender on my stock 350 sbc QJet-M4M3 1983 K20 p/u and...
    • legozombie
    • Thread
    • 350 canister carburetor charcoal canister evap fuel delivery fuel issue quadrajet vapor canister
    • Replies: 29
    • Forum: Carb Fuel Systems
  2. legozombie

    Door Jamb Switch Restoration

    The only problem about buying new switches from what I gathered were the length of the actual switch or the threads not fitting the hole. In some instances they seemed to be too long for the door to close properly or were not the right size for the preexisting hole in the body. I didn't want to...
  3. legozombie

    Door Jamb Switch Restoration

    Have you thrown away parts because "they're cheap" or because you thought they were no longer useful or work cleaning? I just wanted to let everyone know as a PSA that restoring these door jamb switches are insanely easy. Mainly because of how dumb the switches are. No complications at all. Just...
  4. legozombie

    Parking Brake Light Not Coming On

    So I tested the parking brake switch and it produced ground when it was supposed to just as our messiah and savior Paul Hitch intended to. When I tested the prop valve, the gauge side of the circuit was grounded (more than likely from the engaged parking switch) but the prop combo valve was not...
  5. legozombie

    Parking Brake Light Not Coming On

    So I found sometime last week to do a quick test. The switch only had one wire that was brown/tan with a white stripe and it essentially just connects the circuit to the ground. This is looks like it's done by screwing into the parking brake assembly which is bolted to the body which is...
  6. legozombie

    Parking Brake Light Not Coming On

    Good Evening. I am trying to trouble shoot my brake light not coming on on my dash. I have never seen it on once and never again. I have new bulbs + sockets and know that the bulb is working because I have bench tested each light and gauge for functionality so, I know it's not the bulb unlike...
  7. legozombie

    Need source for gauge backing housing w/clock

    @Ron Craven I'm assuming this is the part you're looking for?
  8. legozombie

    Need source for gauge backing housing w/clock

    Duplicate msg sorry
  9. legozombie

    Source for new gauge needles

    I actually ran into a similar issue taking the gauge cluster off. I'm planning on having a friend 3d print some unique needles to fit. Or I may finally pull the trigger on a 3d printer...
  10. legozombie

    Need source for gauge backing housing w/clock

    Did you check truck and car shop? http://www.truckandcarshop.com/
  11. legozombie

    Cup Holder Options

    I bought the backup cam and installed it. I will post later about it. Super easy to wire and install. Here are the two cup holders I considered for my bench. I ended up going with the hard plastic one because 1) It was made in the USA 2) As nice as the boat foam holder one was, I can and...
  12. legozombie

    87 Stock TBI 350 air cleaner lid flip upside down? Does it help? does it hurt? good or bad idea?

    So for anyone looking for carburetor hose or carburetor air intake duct or anything in-between (hey, that sounds right, right?) I've gotten a lot of hits on this part as a carburetor pre-heater hose or duct
  13. legozombie

    87 Stock TBI 350 air cleaner lid flip upside down? Does it help? does it hurt? good or bad idea?

    @Craig 85 or anyone else reading this, what is this part called? I can't seem to find it for my K20 or the air cleaner for that matter. I've looked up variations of snorkel tub and carburetor intake hose. I also think I'm just dumb however that's a different story :D
  14. legozombie

    Cup Holder Options

    That's a good idea. I ended up buying some bench cup holders at the recommendation of another thread and will probably post results when they arrive. There's just something about drilling into the original metal that doesn't sit well with me, but with plastic, I can drill holes all days...
  15. legozombie

    Cup Holder Options

    I was thinking at the bottom of the door like in this pic. I was hoping to get something to hold my protein shake so it doesn't spill everywhere! Having a manual K20 with a floor shifter limits my options
  16. legozombie

    Cup Holder Options

    Anyone think these may be good cup holders if you attach them to a strong magnet? Looking to add cup holders without drilling anything. https://www.amazon.com/dp/B0097YH972/
  17. legozombie

    Nerf bars

    What brand did you use? Was it an easy plug n play installation or did you have to do any modifications?
View older results

Latest posts

Forum statistics

Threads
44,157
Posts
950,582
Members
36,271
Latest member
jstewart7501
Top