Search results
-
International Dump truck
got the heads back, and Dell and I got the engine mostly back together, at least the heavy stuff. Harry Bugger helped.- Craig Nedrow
- Post #4
- Forum: Other Vehicles
-
91 Burban Radio Restoration - Static Gone!
Contacted Joe, going to send him my radio 85 C20 and put Bluetooth in it- Craig Nedrow
- Post #6
- Forum: Electrical & Audio
-
Hi
Geez Mike, it is almost a sin to post without pictures.....so many here that can't read, besides we wanna see! I also am retired and about neck deep in squares. Carry on and were glad you are here.- Craig Nedrow
- Post #13
- Forum: Introduction
-
Help with GM 14 Bolt Rear End
Here is a write up on my rerarend 14FF. Go here start post 35 https://www.gmsquarebody.com/threads/1973-k20-350-to-454-swap.29840/page-3 Identify each cap, put it back where it came off. Measure your pinion depth, new oun should be close for correct tooth contact. Get some Prussian blue, or gear...- Craig Nedrow
- Post #8
- Forum: Differential & Driveline
-
Removing engine and trans.
I did that a couple times, Here is what I did..... https://www.gmsquarebody.com/threads/1973-k20-350-to-454-swap.29840/ Start at post #6. You can pull the engine without taking off the front, Just wanted to clean mine up, and not scrape the firewall or rad support. Help's alot to get an...- Craig Nedrow
- Post #6
- Forum: Engine & Performance
-
-
New For Me 1985 Silverado 20 6.2 Diesel
Finished wire brushing the frame, degreased, and painted. Also painted some under the hood. Thanks Craig85 for the paint tip, covers fast, and has the look I am looking for.- Craig Nedrow
- Post #81
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Well poo Derek, I can not find anything local, but could order Poo Derek, can't find anything local, only online. I have a very tight schedule, so will install and plug it in this winter. However you have been a help in the past and I appreciate it- Craig Nedrow
- Post #78
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
But before I install the tanks, I have to wipe the frame down with alcohol or lacquer thinner, and paint. It rained all day, but slow and gentle, low 50's so good shop weather. Had to turn the heater on to dry the painted items. I have been selling a bunch of farm stuff, and that also takes my...- Craig Nedrow
- Post #75
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Oh yeah, don't get me into car movies Greg!- Craig Nedrow
- Post #74
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Geez Greg that's a mouth full, Thanks! I am hoping to get the gas tanks in this weekend, and install the switch in the dash, that looks like fun, then get the wiring straightened out, as nothing worked before, and this is the first time delving into this debunkel. My new floats have both...- Craig Nedrow
- Post #73
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Here is the filler hose numbers, both the same, and the switching valve. Was hoping for great instructions, very minimal and very blurred and hard to read. I do believe I saw a post with a wiring diagram will look for that. The vent hoses are not here yet, coming from Rock auto. As an aside, hot...- Craig Nedrow
- Post #70
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Here is the frame, I will use this Dupli-Color paint, 1635, Craig 85 told me about it. Just got a case from Summit today. It is like a 30% sheen like a stock truck. Seems to stick well. I can't believe how expensive paint is!- Craig Nedrow
- Post #69
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
What does this thing do?- Craig Nedrow
- Post #68
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Dell has been up twice this week and today was mostly cleaning day. Washing the frame, then we scrubbed it with purple power, wash scrub, you get the drift. Frame is a thing of beauty, almost ready to paint, tank supports washed scrubbed, wire brushed, scrubbed, one more pressure wash. Dried...- Craig Nedrow
- Post #67
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
I am farther along since the last post. Old tanks out, new tanks here this afternoon. Here are the correct numbers for my diesel truck. Tanks are the same. FG are the left and right float. Mine is a two tube, these are three, so will plug the vent, as it is already vented by the fill area. The...- Craig Nedrow
- Post #66
- Forum: Introduction
-
1955 1st series salesman panel
have two and a half 55 1st series pickups as well, selling, on CL and FB, that will go towards the 73 engine. Every part is there, some glass, got stolen, got these probably 20 years ago, did nothing with them, now gotta go.- Craig Nedrow
- Post #2
- Forum: Other Vehicles
-
1955 1st series salesman panel
Took ten years, but got the ol' girl in the shop and getting ready to see if it will run. New brakes, rebuilt new 235 six, 4 speed granny low trans. Interior is a mess, but there is a 260 six in there, along with new parts, and old parts. Hope to get it running and sell it to finance other...- Craig Nedrow
- Thread
- Replies: 1
- Forum: Other Vehicles
-
International Dump truck
Been working on my IH dump truck. Pulled the heads, and took to shop, back in a couple weeks. Then I get to finish hauling gravel about 100 yards, then gonna sell . Good ol' truck but down sizing. I have doon a ton of work, new tires, brakes, transmission, and now engine. I rebuilt the master...- Craig Nedrow
- Thread
- Replies: 5
- Forum: Other Vehicles
-
New For Me 1985 Silverado 20 6.2 Diesel
I have not been setting on my hands, have been working on the square. Pulled the rad, but shop I trust said it was or soon will be shot, it was leaking slowely from a few spots. Ordered a brass/copper original coming from Texas, be here next week. In the mean time, both tanks are slowely...- Craig Nedrow
- Post #65
- Forum: Introduction
-
Windshield seal/rubber replacement. is there a preferred brand or is all the same?
Soft seal is high quality as well- Craig Nedrow
- Post #6
- Forum: Glass & Mirrors
-
Big block Chevy valve lift
are you using a dial indicator on the valve stem? What method are you using to determine lift, and where are you measuring it at? I measure on V-blocks first on a bench, if in the car, I measure off the lifter. Pushrod length is right when your contact pattern on the valve stem is in the middle...- Craig Nedrow
- Post #5
- Forum: Tech Discussion
-
New For Me 1985 Silverado 20 6.2 Diesel
This was off a 94? and they were the right length (99") but 69 3/8 inch and we need 71". I may try to find a 99-presant, as they are the right width, but about two inches longer. I would cut out the two inches, use sheet metal and rivets, and then re-fiberglass and paint carpet . A bit of...- Craig Nedrow
- Post #63
- Forum: Introduction
-
New For Me 1985 Silverado 20 6.2 Diesel
Drive the C20 on the first real long trip to Olympia, over White pass. Truck was a gem, never missed a beat. Picked up a canopy. A few things I need to fix, Fuel gage for both tanks registers open (past full), Radiator has a small leak, pulled it today and will take it to a local shop I have...- Craig Nedrow
- Post #60
- Forum: Introduction
-
8.1 Vortec VS 383 Stroker VS 6.0 Iron LS
I have been looking at that same set up, drooling really. Want Airflow Research 335 heads on it though, cause I likem.- Craig Nedrow
- Post #19
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
