TotalyHucked
Full Access Member
- Joined
- Feb 24, 2020
- Posts
- 3,791
- Reaction score
- 12,258
- Location
- Auburn, Georgia
- First Name
- Zach
- Truck Year
- 1985
- Truck Model
- Sierra 1500
- Engine Size
- 5.3
^This
Spark plug gap closed fresh rebuild
- Thread starter Cdog_96
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Craig Nedrow
NADAR UNDER THE RADAR
- Joined
- Sep 1, 2018
- Posts
- 1,103
- Reaction score
- 2,359
- Location
- Washington State
- First Name
- Craig
- Truck Year
- 1973 (have two), 1985
- Truck Model
- K10, K20, C20
- Engine Size
- 350, 454, 6.2 Detroit
I have been the recipient of much good humored help on this forum, but as a machinist, and Like Ricko says "just because it's old, doesn't mean it's bad, and just because it's new, doesn't mean its good. I knew nothing when I started, now I know that, after 60 years of wrenching, 40+ years machining, there is lots to learn. Personally if that was my engine, it would be coming apart. If something has hit the piston, I would not want to find out when a hole has developed and you are oil blowing everywhere. Happened once to me.
mlparkey
Junior Member
- Joined
- Oct 28, 2021
- Posts
- 9
- Reaction score
- 8
- Location
- Oak Lawn
- First Name
- Mark
- Truck Year
- 1986
- Truck Model
- C10
- Engine Size
- 5.7
A spark timing issue is not going to cause that. That's impact damage. The only thing that's going to impact a sparkplug electrode is the piston or something floating around in the cylinder. If you didn't drop that sparkplug before installation then there's a mechanical issue with that cylinder.
- Joined
- Jun 18, 2024
- Posts
- 26
- Reaction score
- 45
- Location
- St Louis
- First Name
- Jim
- Truck Year
- 1985
- Truck Model
- C15
- Engine Size
- 350
Don't know exactly - but north of 175 psi. Take out all plugs. Crank on each cylinder with the tester installed, let it pulse 4 times. you should not see a variation of more than 10% hole to hole.
nvrenuf
Full Access Member
- Joined
- Jul 30, 2010
- Posts
- 1,981
- Reaction score
- 2,522
- Location
- Mobile, Al.
- First Name
- John
- Truck Year
- 1991
- Truck Model
- K5
- Engine Size
- 454
@Cdog_96 any updates?
Rusty Nail
Full Access Member
- Joined
- Jan 29, 2015
- Posts
- 10,041
- Reaction score
- 10,138
- Location
- the other side of the internet
- First Name
- Rusty
- Truck Year
- 1977
- Truck Model
- C20
- Engine Size
- 350sbc
Meh
Cdog_96
Member
- Joined
- Jan 15, 2022
- Posts
- 46
- Reaction score
- 31
- Location
- Aiken
- First Name
- Clay
- Truck Year
- 1983
- Truck Model
- K10
- Engine Size
- 454
Sorry have been busy, I checked the cylinder and looked good with bore scope. The timing was way too far advanced, the tbi computer was putting it way out of spec. I got the timing right and all is good, plug looks good and no misfires
nvrenuf
Full Access Member
- Joined
- Jul 30, 2010
- Posts
- 1,981
- Reaction score
- 2,522
- Location
- Mobile, Al.
- First Name
- John
- Truck Year
- 1991
- Truck Model
- K5
- Engine Size
- 454
@Cdog_96 Glad it's running good now.
Just to say it, while setting the timing are you disconnecting the wire by the harness bulkhead connector down below the wiper motor / master cylinder? (I think it's tan /white stripe)
Just to say it, while setting the timing are you disconnecting the wire by the harness bulkhead connector down below the wiper motor / master cylinder? (I think it's tan /white stripe)
BillK
Member
- Joined
- Feb 11, 2021
- Posts
- 43
- Reaction score
- 27
- Location
- Waldorf Md
- First Name
- Bill
- Truck Year
- 1985
- Truck Model
- Blazer
- Engine Size
- 350
Similar threads
