Recent content by Danderson
-
High Oil Pressure and Leaking After Oil Change
That was my first thought also, but I changed the oil and filter again and this time went with a WIX filter. It didn't help. I have exactly the same symptoms even after changing the filter for a second time.- Danderson
- Post #5
- Forum: Engine & Performance
-
High Oil Pressure and Leaking After Oil Change
I've got an issue that has me stumped. I have a 1977 K10 that has a 350 Goodwrench crate motor installed by a previous owner so mileage is unknown. It's my daily driver and runs great. It has had a rear main seal weep for a while, but nothing more than a few drops overnight so I've put off...- Danderson
- Thread
- Replies: 14
- Forum: Engine & Performance
-
Well, Here We Go!!
Welcome from the great state of Georgia! BTW, I've seen those factory bed rails go for about what you paid for the whole truck. Don't throw them out!!- Danderson
- Post #25
- Forum: Introduction
-
Help finding a part, new or used
I wish you good luck......I've been looking for one on and off for over two years without success. -
Chrome ring around the Rim
If I recall correctly, the 3" rings have a hole where the valve stem goes through and the metal completely wraps around the stem. The 2.5 " rings have a half-circle cut out on the inner lip for valve stem clearance, but the metal doesn't completely encircle the stem. It's been a year or two (or... -
Retrosound Hermosa or Custom Autosound?
I put a Retro Sound Hermosa in my 77 K10 about a year and a half ago. Getting the two shafts set up just right was a bit of a pain, but I'm very OCD about my truck so I probably spent way more time on it than I should have. Looks good, works good, sounds good. I'm happy with it.- Danderson
- Post #4
- Forum: Stereo & Entertainment Systems
-
One legged no more.
That's an awful cheap price for a Yukon Grizzly locker. You got a great deal!!- Danderson
- Post #3
- Forum: Differential & Driveline
-
Introduction
Welcome from Georgia. Where you at in Arkansas? I was born and raised in Conway.- Danderson
- Post #10
- Forum: Introduction
-
-
1977 K5 3000$ OBO!!
I'm only two hours away and have been looking for a decent K5 project so I both emailed and texted the the individual early yesterday morning. If the owner would respond, I'd run right over and buy it. So far no response at all...........- Danderson
- Post #8
- Forum: eBay & Craiglist Listings
-
Part Identification...Please
Looks like the neutral safety switch. It mounts to the top side of the steering column near the firewall.- Danderson
- Post #2
- Forum: Tech Discussion
-
What have you done to your square lately??
Spent way too much time this afternoon chasing down an electrical gremlin. I was driving along and the radio suddenly went dead. Checked the fuse block and found a blown fuse, so I replaced it and all was well.......for about ten miles and the radio went dead again. Same fuse blown. The radio... -
Classic Parts Repro Steering Wheel
The tach markings go from 0 to 50 in increments of 5. The markings are x 100 RPM so the "5" marking is 500 RPM and the "50" marking is 5000 RPM. The truck idles at 700 RPM so the lower markings are very useful. The factory tach on my 2011 Silverado goes from zero to 6 with hash marks in between... -
What have you done to your square lately??
Put a new sew-on leather wrap on my steering wheel. Came out great and I really like how it "thickens up" the feel of the wheel. -
Delay Wiper Module
I could be mistaken, but I'm pretty sure the wiper park positioning is a function of the wiper motor and not the module. I also don't believe the windshield washer is controlled at all by the module other than direct power pass through.- Danderson
- Post #16
- Forum: Gauge, Speedo & Instrumentation
