Recent content by ballencd
-
Davis Off Road, crossover steering???
The steps look nice but I can't imagine spending that kind of money on a set.- ballencd
- Post #7
- Forum: Suspension, Steering & Brakes
-
Dual fuel tank filling
Again, for the record. A M1010 is a K30 truck with an aluminum box on the back.- ballencd
- Post #49
- Forum: Carb Fuel Systems
-
Davis Off Road, crossover steering???
That's one pricey set of steps at $3000! Not for me. Looks more like an AD for Davis than info for the group!- ballencd
- Post #5
- Forum: Suspension, Steering & Brakes
-
Aftermarket Lock Kit
Anyone have pictures of the wiring to the door for these locks?- ballencd
- Post #6
- Forum: Retro-Fit & Aftermarket Accessories
-
Help with ignition lock removal - 1984 M1010
The truck uses one battery for a 12V source for everything in the cab.....lights, gauges, heater fan, horn,....etc. nothing in the truck runs on 24V except the starter....(the glow plugs came from factory with a load resistor to drop the GP load voltage down to 12V but I have removed that and...- ballencd
- Post #8
- Forum: Tech Discussion
-
Just bought this 87 square body in TN and it’s now home in North Carolina where i’m going to restore it
Welcome from Columbus, NC.- ballencd
- Post #25
- Forum: Introduction
-
Dual fuel tank filling
Just for the record......I dumped the idea of using my spare tank to carry gas and will just take a few 5 gallon cans. I don't like messing with the cans because of all the safety stuff that causes them to drain slow and leak on my hands and feet but I will not be doing it enough to follow...- ballencd
- Post #47
- Forum: Carb Fuel Systems
-
Help with ignition lock removal - 1984 M1010
It's been a long while now but a busy year. I figured out that even though it is a 1984, it has an older column in it, which uses the older style key lock cylinder. I ordered the right parts and with Strick's help above I figured out how to get the lock out. It is all back in now and working...- ballencd
- Post #6
- Forum: Tech Discussion
-
New Dual Tank Install....I have a question...?????
I don't know the warranty on the valve. I got it from LMC awhile back and just now getting around to installing it.....mostly because I did not have a method to fill the right side. I hve some M1009 parts that I am going to try to make work for that. Here is the LMC info: 32-3293 Selector...- ballencd
- Post #3
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
New Dual Tank Install....I have a question...?????
Just about to install the second tank in my M1010. 6.2 Diesel engine. Looking at the valve I purchased there is a sticker on it that states "Warranty void if filter is not installed between the tank and the valve". The 6.2 vehicles (CUCV's) have a sock in the tank and the main filter in the...- ballencd
- Thread
- Replies: 5
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
Banks Sidewinder Turbo
Still for sale? I am needing a Banks kit for my M1010.- ballencd
- Post #12
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
-
Squishy brakes
Ricko1966, You should have let it go back in the thread on post #14 like you said you were going to do. IMO you started out in a bad mood. I hope you get over it soon. -
Fuel Tank Selector Valve Shield
Long time since this was written but I am just now working on installing a second fuel tank in my M1010. Here are pictures of the cover and location for future reference. My cover was bolted on with the chassis threaded, no nuts at all and easy to get to. Looks like the two holes in the top...- ballencd
- Post #9
- Forum: Tech Discussion
-
