8
Supporting Member
83K31003
Supporting Member From Florida
Supporting Member
- Joined
- Last seen
- Viewing thread Chassis brackets and rubber motor mounts.
Latest activity Postings About
-
-
883K31003 reacted to bucket's post in the thread Chassis brackets and rubber motor mounts. with
Like.
Big block on small block mounts. Stock covers, but plenty of room for tall fabricated covers. -
883K31003 replied to the thread How Will My Square Body Look With XX Lift and XX Tires?.‘83 GMC ( wrong grille ) K-3500 with a double stack of Superlift 8” front springs and a double stack of 56” long 30-series rear springs...
-
-
883K31003 reacted to nvrenuf's post in the thread How Will My Square Body Look With XX Lift and XX Tires? with Like.
Ok, I'm sitting here bored looking at old pics so I decided to pic ***** a little. My old wheeler: '80 K10 w/ 1 tons, 10"...
-
883K31003 reacted to 84_3500's post in the thread I just won a 1985 1 ton C/K Four door from the auction. going to pick it up next week ill post pics. Are there any four door square body guys on here? with Like.
Here is out 84 we just drove 3500 miles to Utah and back with a 1968 Yellowstone camper on tow.
-
883K31003 reacted to Texan Cris's post in the thread I just won a 1985 1 ton C/K Four door from the auction. going to pick it up next week ill post pics. Are there any four door square body guys on here? with Like.
Here is one that I plan on sending to Mecum Dallas.
-
883K31003 reacted to Fubar500hp's post in the thread I just won a 1985 1 ton C/K Four door from the auction. going to pick it up next week ill post pics. Are there any four door square body guys on here? with Like.
Welcome from TN
-
883K31003 reacted to Barryr71's post in the thread I just won a 1985 1 ton C/K Four door from the auction. going to pick it up next week ill post pics. Are there any four door square body guys on here? with Like.
Here’s my 87.
-
8Since you have them in your possession, it seems a test fit is in order :)
-
8Mine is an aluminum 5" at 72.5" center to center but that's because no one would build a steel one longer than 60" for over 500HP. Best...
-
8Thanks for confirming. Looks identical to the one I have. Yeah I knew I had a problem when Mark Williams' told me to pound sand when...
-
883K31003 replied to the thread LWB driveshaft question.I miss read the 2WD and 72” tube portion - I was thinking this was a 4WD application with a shorter tube dimension. My apologies, Tom
-
883K31003 replied to the thread LWB driveshaft question.‘80~’88 K-30’s with a regular cab and a fleetside bed SRW & DRW ran a two joint slip yoke shaft setup that was steel but only 4”...
-
883K31003 reacted to nvrenuf's post in the thread I just won a 1985 1 ton C/K Four door from the auction. going to pick it up next week ill post pics. Are there any four door square body guys on here? with Like.
I don’t run around in Houston but I wish my MegaCab had an 8’ bed. IMO, short beds don’t look proportionate to 4 door cabs.
-
883K31003 reacted to nvrenuf's post in the thread I just won a 1985 1 ton C/K Four door from the auction. going to pick it up next week ill post pics. Are there any four door square body guys on here? with Like.
I used to be a (1991) crew cab guy, I wish I still was.
-
8Torque is your enemy here. Aluminum bell housings both automatic and manual really aren't that strong. I had to replace bell housings on...
-
-
Loading…
-
Loading…
