Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
75gmck25's latest activity
75gmck25
replied to the thread
Edelbrock carbs on a 350 sm blk
.
I have had an AFR gauge for quite a while, and it’s really useful. Start out by checking the transfer slot exposure to ensure it has a...
Dec 4, 2024
75gmck25
replied to the thread
Edelbrock carbs on a 350 sm blk
.
A frequent complaint with the Edelbrock is a bog when transitioning from steady rpm cruise to quick acceleration. Changing the hole...
Dec 3, 2024
75gmck25
replied to the thread
Which ground do I start with?
.
IIRC, the cargo lamp housing is insulated from the truck with small spacers to stop it from being grounded. It always has power on the...
Dec 3, 2024
75gmck25
replied to the thread
Rochester Quadrajet Woes
.
Take a close look at the throttle linkage side of the carb and get the Quadrajet number. This tells you which carb you have (original...
Dec 3, 2024
75gmck25
replied to the thread
Big block running hot. Can’t figure out the issue
.
Not to nitpick too much, but stoichiometric (best) AFR for gasoline is about 14.7. 14 is slightly rich, but that should actually help...
Dec 2, 2024
75gmck25
replied to the thread
Tool for adjusting idle
.
Original Quadrajet idle screws are usually a double-d shape, and there is a flexible carb tool that has that special end on it. When I...
Dec 2, 2024
75gmck25
replied to the thread
Steering Help
.
One simple check - make sure all the air is out of the system. GM book says to jack it up with both front wheels off the ground. Then...
Dec 1, 2024
75gmck25
replied to the thread
brake pedal has no pressure
.
All good suggestions. If the seal is torn or damaged inside the master cylinder it will not seal against the cylinder, and the pedal...
Nov 29, 2024
75gmck25
replied to the thread
82 Sierra Grill alternatives
.
When you start swapping grills, remember there are sometimes also differences in mounting brackets. I have about a ‘79 grill on my ‘75...
Nov 27, 2024
75gmck25
replied to the thread
First real drive! Not tragic but not good. I think I need carb advice.
.
One strong recommendation is to immediately convert it to HEI ignition. It is very reliable, and does not require periodic adjustment...
Nov 26, 2024
75gmck25
replied to the thread
First real drive! Not tragic but not good. I think I need carb advice.
.
Also get number off the side of the Quadrajet. For example my ‘75 Quadrajet is 7045583 YZ.
Nov 26, 2024
75gmck25
replied to the thread
A/C Question
.
I do not have a write up, but I have a lot of pictures and a list of everything used. This could motivate me to write it all down in...
Nov 26, 2024
75gmck25
replied to the thread
A/C Question
.
The old A6 compressor is a true boat anchor, and it has heavy brackets to keep it supported. It’s also now old and not very reliable...
Nov 26, 2024
75gmck25
replied to the thread
First real drive! Not tragic but not good. I think I need carb advice.
.
The air cleaner has a thermostatic valve in the snout to control heated air, and it’s connected to vacuum at the carburetor. No reason...
Nov 25, 2024
75gmck25
replied to the thread
LMC headlights/harness kinda wonky
.
Bought one of the LMC kits many years ago. Wiring seemed a little chintzy (not really HD) at the same, but it’s lasted a long time...
Nov 25, 2024
Latest posts
What new tools have you got lately?
Latest: bucket
A moment ago
Garage
What have you done to your square lately??
Latest: Mr Clean
2 minutes ago
Garage
Spark plugs
Latest: bucket
5 minutes ago
Engine & Performance
k35 from Fresno, greetings all
Latest: bucket
11 minutes ago
Introduction
Sagging doors: where to start?
Latest: EastAustinSawdust
12 minutes ago
Paint and Body
Forum statistics
Threads
44,630
Posts
963,179
Members
37,197
Latest member
professor
Members
Top