Squeal

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

ArmyChief

Junior Member
Joined
Dec 25, 2016
Posts
12
Reaction score
0
Location
Richmond, vA
First Name
Bob
Truck Year
1982
Truck Model
K10
Engine Size
305
New to the site, so hopefully this question is in the right thread. If not, mods please move.

1982 K10 with 305 and manual transmission has a horrible squeal while at idle. Replaced the belts with no change. Squeal sounds like a belt squeal, but goes away with the slightest pressure applied to the clutch pedal. There is no sounds within the clutch that make me think it's a throwout bearing. Any help would be greatly appreciated.
 
Last edited:

Rusty Nail

Full Access Member
Joined
Jan 29, 2015
Posts
10,041
Reaction score
10,134
Location
the other side of the internet
First Name
Rusty
Truck Year
1977
Truck Model
C20
Engine Size
350sbc
K.

There is a lot of stuff turning on the front of that engine. Many parts in motion.
If it were ME, I would remove the belts (one at a time) and observe for change.

Good luck!
 

87ChevyR10

Full Access Member
Joined
Sep 2, 2013
Posts
1,125
Reaction score
66
Location
Kansas
First Name
John
Truck Year
NA
Truck Model
NA
Engine Size
NA
IF the vehicle has A/C, the pulley bearing on the compressor (or the compressor itself) can seize causing belt squeal. Or the power steering pump can cause belt squeal if it's trying to seize. However, if it goes away just pressing the clutch, that would make me think it's clutch-related somehow. The RPM difference shouldn't be significant.

Do as Rusty suggested. You won't hurt anything removing the belts.
 

austinado16

Full Access Member
Joined
May 25, 2012
Posts
611
Reaction score
222
Location
Central Coast, CA
First Name
Todd
Truck Year
1990 w/307k miles on the clock
Truck Model
GMC V1500 Suburban SLE
Engine Size
5.7L TBI/4L60/3.42's
The suggestion of removing all the belts is good. If you still have a squeak, and I think you will, crawl under and inspect the clutch arm adjustment in order to make sure that throwout bearing isn't being partially engaged at all times. You may have a failed slave cylinder, or a failed flex hose between the slave and the hard line from the master cylinder......they'll act like a check valve and not completely relieve pressure, so the clutch arm is always held partially "engaged." It won't be the pilot bearing, because those are only actually spinning during the short period between shifts, or when the clutch pedal is fully on the floor.
 

stlbob

Full Access Member
Joined
Nov 18, 2016
Posts
56
Reaction score
3
Location
St.Louis
First Name
bobby
Truck Year
91'
Truck Model
k3500 4x4 Burban'
Engine Size
454
Throw out bearing,just did a truck about this age in the shop..Same type of complaint..If it has v groove belts only remove one at a time.Restart and listen..
 

Mr Clean

Super Moderator
Staff member
Super Moderator
Joined
Aug 18, 2010
Posts
10,322
Reaction score
10,214
Location
North East Texas
First Name
Shawn
Truck Year
1982 & 1985
Truck Model
K10 Extra Cab w/ Proper SWB, & 85 K5 Blazer
Engine Size
454 BBC, & 383 Stroker
Yeah, I was thinking throw out bearing also. If you are barely touching the clutch pedal, and it goes away, it has nothing to do with your belts.
 

ArmyChief

Junior Member
Joined
Dec 25, 2016
Posts
12
Reaction score
0
Location
Richmond, vA
First Name
Bob
Truck Year
1982
Truck Model
K10
Engine Size
305
Thanks, all. Replacing the entire clutch this weekend.
 

Forum statistics

Threads
44,168
Posts
950,764
Members
36,283
Latest member
Cantrell299
Top