swap

  1. barrymattern

    C10 to K20 Body Swap – Driveline Issues

    TL;DR: I'm in the middle of body swapping a 1985 C10 cab & bed onto a 1984 K20 frame. The frame was purchased without a front clip, engine, or doors so specific truck options are not known. After decoding the VIN I confirmed the donor truck/frame is a Canadian truck that had a 6.2L diesel, and...
  2. Zayshley

    '76 K1500 NP203 to NP205 swap

    I just recently bought a NP205, that was bolted to a 400/th350 in a '80 Blazer, that I plan in putting in my truck to replace the beat NP203 which has the locking hubs conversion kit. Besides drive shafts, is there anything else I need to make it work?
  3. ceejay

    Opinions on an Engine Swap for 81 C10

    Right now, I have an extremely tired 305 and I'm ready to swap it out. Now I've bounced around different ideas, but not sure on which route to take. I think I've narrowed it down to wanting a 350. I don't want to do LS swap or big block. I've done some research and I've come down to: 1. Buy a...
  4. C

    transmission engine options

    I have an 1984 c10 3-speed column shift. Im looking to do an engine swap, but I want to keep the 3-speed. I currently have a 250cu l6. What engines would mate with my tranny? Thanks for the help!
  5. Preston Tucker

    HELP! Nv4500 Swap, so many transfer cases so little time.

    Ive been looking on here for hours and could not find a thread with the information I need, maybe you all can help! Anything is appreciated. I am converting my 1974 k25 from a burnt th350 to a Nv4500. I have all the hydro stuff for the cab out of an 87 parts rig and tonight I bought a whole...
  6. Powerhouse Ranch

    Square Body Front Clip on a Medium

    NOW I know that it's a big thing for people to put medium duty front clips on pickup trucks (of all makes, I've seen old Fords, and new Chevys) BUT has anyone ever considered taking a front clip of a 73-87 Square Body and placing it on a 73-87 Chevy/GMC medium duty truck? Could you imagine how...
  7. devin bianco

    Np203 to Np205 , transfer case swap

    this might have been talked about before, but it would be nice for some clear information on it. first here are some specs: Ive got a 79 k10, sb350 going to a th350 going to a np203 full time no slip yoke. we are doing a np205 swap, we have the truck down to frame with no current drivetrain...
    • devin bianco
    • Thread
    • driveshafts help linkage np203 np205 np208 swap t-case th350 transfer case
    • Replies: 24
    • Forum: Transfer Case
  8. J

    Cab swap help and pointers

    Hi everybody, I'm new here to the forum but I have some questions but first I'll explain my situation. Currently right now I'm building a truck, basically from the ground up from about 3 different donor trucks. Right now I have rolling K20 chassis, with tank and fuel lines, that's it. I'm...
  9. Subourbon

    Swap body instead of engine, tranny, front and rear ends etc...

    Hey guys, So I jumped on the cummins bandwagon and starting looking into what I'd need for a swap. turns out its a lot. Things I hadn't even thought of! Anyhow, someone mentioned I'd need a donor truck etc... Then when the comments piled up and I saw how much work it is, which is fine, its a...
  10. Preston Tucker

    Air Conditioning Swap

    Hello everybody! I have a 1974 GMC k20 project truck and recently picked up a rolled 1987 c10 with an air conditioning unit, so long story short. I want to do an ac swap! I have all the stuff for it but if anybody has gone about a swap like this before that would be helpful for you to drop some...
  11. SubDominant

    Cadillac CTS seats in an 89 v1500 Burb!

    I have been scouring this site for seat info for my 89 Burb. I have thoroughly enjoyed the posts that I have found. But I happened across some seats that I just had to figure out how to install in the big boy. First of all, my truck came with some really plush captain's chairs for seating. Only...
    • SubDominant
    • Thread
    • buckets seat seats swap
    • Replies: 28
    • Forum: Seats
  12. caleb chapdelaine

    K10 leaf spring swap

    Looking to build my k10 to be a trail rig for a while. The truck came with 6 inch lift blocks on the rear. But I’m looking to swap the 52 inch spring to 63 inch springs and build the shackle flips. So that it rides better and allows more articulation, could I see some ideas and hear some thing...
  13. jairie laplante

    i6 to 350 swap need help

    i have a 1981 with the 250 i6 and i want to swap to a 350. i have been able to find that the motor mounts work the same but cant seem to find if my transmission will just bolt up to the 350. i have the 3 speed manual Saginaw transmission and want to keep it. so my question is what will i need to...
  14. 87C10LS

    A/C hvac

    Ls swap is done. 87 Chevy r10 that is an a/c truck. All that wiring is intact. I have the upper a/c mount for the motor that will accept the Sanden or pancake style compressor. Can I use all the original A/c wiring with a newer serpentine style compressor?
  15. Dleighton

    454 with 10 bolt rear end?

    Hi, I was wondering if anyone had any insight on how well a 10 bolt rear end would last after a 454 motor swap. I just had it rebuilt last year, 4.56 gears, 35 inch tires. I know it's not an ideal set up, but I am having trouble finding a good deal on a different set up. The motor is a stock...

Latest posts

Forum statistics

Threads
44,144
Posts
950,240
Members
36,255
Latest member
WhatsEnoughChevys
Top