Search results

  1. C

    Saginaw Steering Gear Rebuild - Special Tools?

    YouTube has all kinds of videos on rebuilding Saginaw steering boxes. The only "special" tool needed would be a spanner wrench but you can use a needle nose pliers instead. Snap ring pliers are needed as well.
  2. C

    Remembering Kerry "Mike" Perkins (Paladin)

    Sorry to hear this about Mike "Paladin" Perkins. He sold me a coveted '84 GMC grill a couple years ago. Rest in peace buddy.
  3. C

    700r4 Governor cap

    Heat it up with a small torch on low heat. After a few minutes try again with your prying tools.
  4. C

    Does anyone know if i have a 1 piece or two piece vent window?

    Take it apart and look at it. Since it's already broken and will be taking it out anyway. No sense in guessing what you have. My 2 cents.
  5. C

    Trailer Wiring Adapter

    The plug configuration is different after '84. 84 and under is round with I think spade connectors whereas the 85 and up are a smaller diameter with pin connectors.
  6. C

    Loose cab mount

    If it were me, I'd go at it with a regular 1/2" ratchet but only after I heated the bolt up and then I would tighten then loosen then tighten some more, work it back it forth until it comes completely out. Then run a wire brush over the threads and then wash it off with PB Blaster. Then spray...
  7. C

    85 GMC k1500 flywheel cover

    I have the same thing on my truck. The dust covers are different. I believe the 2 wheel drive 700's had a dust shield made of light steel with two bolts/ screws on each side holding it on whereas the 4 wheel 700 case has 3 bolts on each side holding the dust shield on and was constructed of...
  8. C

    Busted Alternator Bolt

    If the long bolt pictured is the one that sheared off, I'm thinking there's only a thread or two in the head. Shouldn't be too hard to back that broken piece out.
  9. C

    For Sale

    Found this on Columbia, Missouri Craigslist! https://columbiamo.craigslist.org/pts/d/jefferson-city-chevy-step-side-bed-8ft/7593704487.html
  10. C

    Anyone Use Classic Industries Dash Pad

    Thank you very much.
  11. C

    Anyone Use Classic Industries Dash Pad

    @CheemsK1500, Nice interior. What is the paint code for your 84? Thank you
  12. C

    Fuel hose

    Looking at replacing fuel hoses on my 84 K2500. Does anybody here have an outlet or source for thee premolded fuel hose? Thanks all.
  13. C

    wood dimentions

    No, they just give it that dimension before planning after it being cut from the log. Same as a 2x4 actually being 1.5"x3.5".
  14. C

    wood dimentions

    It's 1 inch thick.
  15. C

    Anyone in Missouri???

    Central Missouri here. Near Columbia.
  16. C

    Picture Please: No Spare Tire Holder

    Look on LMC Truck, they will have pictures or drawings of everything you need.
  17. C

    Running boards clean up and installation

    You might also try naval jelly, supposed to be real good at cutting rust.
  18. C

    swapping gear ratio in the 14 bolt??

    There's a guy on here from Australia, posted the other day with pretty much the same set up as you and he's going with a 3:21 ratio.
  19. C

    Question about R4 "Pancake" AC compressors

    The only thing I know about them is maybe a reverse rotation be cause of either being mounted on the opposite side of the engine or perhaps from the serpentine belt system.
  20. C

    86 4.3 v6 2 barrel options/emissions delete

    Depends, does your truck have a carb now? I would assume it does being an '86. But, it's most likely a 4 barrel so if you want to go to a 2 barrel you would have to change your intake to accommodate that.
  21. C

    Cracked windshield

    Yep, the same company.
  22. C

    Cracked windshield

    Whatever you do, don't go to Safelight. It took 2 different guys 4 windshields to finally get one right put in my truck. I would not have used them at all but it was an insurance job from a road overlay outfit that used too big of gravel on the road.
  23. C

    Here's a 73-87 bed mat

    Too bad the ad only states for short bed trucks,
  24. C

    Starter shim questions

    Heat will be your friend. Put a small butane or propane torch on the spot where the bleeders screw into.
  25. C

    1987 GMC V2500 4X4 TBI 350 -RADIATOR SIZE ???

    Can you just measure the stock one that's in the now? Just curious.

Latest posts

Forum statistics

Threads
45,436
Posts
983,369
Members
38,473
Latest member
ALAU
Top