Search results

  1. henrym

    Aftermarket EFI and dual internal pump tanks

    use the corvette fuel filter/regulator, never had a problem with my set up, using a Fitech
  2. henrym

    I'm at a loss..

    I know thread is a couple months old,,but I'm assuming the brake shoe hardware was installed correctly? this opposite sides mirror images of each other. It's easy to but a spring on backwards, causing a bind, or the self-adjuster was flipped, or even the bar and related spring installed...
  3. henrym

    Oil leaks

    Excess blow by may be forcing oil out breather, follows down the valve cover by fan/angle.
  4. henrym

    Driveline vibration help

    a slight bend to your rims can cause a vibration, but hopefully the guys who mounted/balanced your new tires paid attention and checked to wobble or ocsillation when spinning the tires., But other than that try some shims between the axle pad and the leaf spring to lessen the angle
  5. henrym

    front/rear braking bias

    I have my 81/84 K20, and I have changed the brake proportioning valve hoping to have better braking, with no change. I have the metic 14 bolt with the 13" brake at the rear. My problem is the system is heavily biased to the rear, which is fine if I have a ton of weight at the back, BUT,,,,,,my...
  6. henrym

    700R4 and Correct Gearing

    driver side it where that governor is placed, there servo is on the pass side
  7. henrym

    "Rebuilt" 700r4 issues

    That would be the point of having the TC lock up vacuum switch in place, when vacuum drops as you step deeper into the gas pedal, vacuum pulls the switch open, unlocking the torque convertor
  8. henrym

    Torque Converter lock up switch

    yes
  9. henrym

    Hola from New Mexico

    Welcome! Home used to be Albuquerque, now in WV
  10. henrym

    Torque Converter lock up switch

    Can anyone share the schematic for hooking up the TCC vacuum switch and the 4 pin connector on a 86 700R4 trans? Any info would be helpful, thanks!
  11. henrym

    How I hate electrical issues...

    I totally understand about hating electrical, regarding the harness running to the rear, I did exactly that, except I used a 7 wire trailer harness, so i had an extra wire for my electric trailer brake, and for a rear mount light that I use with a toggle for extra lighting while backing up in...
  12. henrym

    350 intake parts questions.

    1ST is a ported vacuum switch, part of emissions system, often deleted. 2nd pic I believe is a vacuum port for distributor, as some quadrajets apparently did not have vacuum ports, but I have never seen one of those in person. someone will chime in to offer another possible function.
  13. henrym

    Prepping for 700r4 goodness

    The radiator will "pre-cool" the ATF to 190f-210f, then will pass through the auxillary cooler, further bringing down temp. All coolers are gvwr rated, and in AZ, or towing, it wouldn't hurt to go large on cooler size. I run a 11"X12" stacked fin cooler, and have never had a problem running...
  14. henrym

    extended bumpstops

    hi, thanks, but YIKES!!!! $240.00 is a bit too steep for a hauler/off-roader kind of truck.
  15. henrym

    extended bumpstops

    I've had a Pro Comp 6" lift on my truck for a number years now. I installed poly bumpstops, 4" I believe, and of course the ones at the rear are no where close to actually doing anything. Anyone have ideas on how to lower the rear bump stops? I thought of buying heavy duty steel rectangular...
  16. henrym

    A/C

    piece of cake, go to a boneyard, get all related parts, if possible take the compressor as well, as you will be charged a core charge, swap out all ducting, head unit, evap box with relays etc. minimal work is need modify, as most should be a bolt on. don't forget the crank and p/s pulleys as...
  17. henrym

    damn you engine masters!

    Is your starter solenoid touching the header? It looks super close, any head soak issues?
  18. henrym

    86 GMC K1500 Crate 350-Adding HP without Removing Engine

    You don't need a carb bigger than 600 cfm for an engine with that small an output, 600 cfm will probably be good up to 400 hp
  19. henrym

    Speaker help

    I just purchased speaker brackets from [email protected], thanks again for the heads up guys!
  20. henrym

    Brighter lights all around

    You can't go wrong with the LMC harness for your lights. Simple to install, just pick your routing carefully so it doesn't chafe on anything. I use the Lmc headlights and used Hella h4 bulbs purchased from Whitney, the are 55w low beam and 100w highs. Good coverage, but I'm not a fan of the...
  21. henrym

    Rear Speaker Source

    thanks for the info guys, just ordered my brackets!
  22. henrym

    Rear Speaker Source

    I have installed a new stereo with BT tech, and I was wondering about the rear speakers behind the seats in the corner of the cab. Does anyone sell a speaker in the 200w, or greater range that will fit in the stock location brackets? If not, care to post some examples of what you installed? I...
  23. henrym

    Kill Switch

    the old dimmer stitch on the floor could be used as a ignition hot wire interrupt switch on models with the dimmer on the t/s stalk. on models with the floor switch already in place, a hidden toggle switch could be used.
  24. henrym

    What have you done to your square lately??

    installed my new Intellitronix Dash, loving it!
  25. henrym

    Digital Dash

    I do have a 20 second vid on my phone I'll upload. Just a matter of getting the right format to download I guess.

Latest posts

Forum statistics

Threads
44,560
Posts
961,059
Members
37,048
Latest member
oramirez
Top