Search results

  1. 8

    Dome light upgrade

    I bought some LED SMD boards and they worked out amazing. cheap too L.E.D. dome light upgrade project - check - The 1947 - Present Chevrolet & GMC Truck Message Board Network L.E.D. dome light upgrade project - check The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board...
  2. 8

    0411 pcm labels? how to order the correct one without using a vin number?

    not sure, i have an extra 0411 pcm somehow in my collection of stuff, if you need any numbers off of it let me konw. it was most likely off of a 5.3 4l60e DBC are you sure the express vans had 5.7 ls1? and not 5.3...... or 6.0...? never heard of a van with 5.7 from memory, the PCM only matters...
  3. 8

    Squishy brakes

    when bleeding the brakes, are you using the combo valve centering tool, it keeps the valve centered when bleeding the brakes. it may shift one side causing a brake issue. what rear caliper did you use, are the brake nipples not pointed up when they are installed? maybe look into hydroboost...
  4. 8

    Dome light went cross-eyed.

    I bought some LED SMD boards and they worked out amazing. cheap too http://67-72chevytrucks.com/vboard/showthread.php?t=671364 clint
  5. 8

    In Search of Original Brake Lines 81-87 C10 Power Disc Brakes

    hope yours turns out better than the other 2 companies I tried, I wish I could put em on blast, but it would take to much effort to dig up the email/invoice... both kits were returned and refunded. I bought one from summit racing and another vendor directly. Trash flares (burrs inside) and the...
  6. 8

    R12 recharge from high side?

    when you charge the car, it should be inverted anyway, where the hose that is feeding the car or a/c machine is on the bottom. Car off, it doesn't matter that much, you can charge from the high side, low side, both at the same time if you want. Default on the r-134a Robinair machine is charge...
  7. 8

    Help with these connectors

    id recommend taking a picture of what the front of the connector looks like aswell. The black one might be for the cruise control connector. it would connect to the end of the switch wiring
  8. 8

    Lower steering shaft

    From what I remember taking mine apart, no, it will not just slide in / out. To replace it you would need to disassemble the column 100%. that shaft is similar to the intermediate shaft that connects the column to the gear box. assembled and set with plastic to make it solid, yet can collapse if...
  9. 8

    About to ruin one of the nicest C3500's with an Ls.. Pictures

    checkout coldhose.com adapters they have a few adapters and I'm sure one of the 3 will work. If you have the oem hoses, they can probably be repurposed.. I wound up re-purposing the L83 suction hose and discharge lines by adding new tubing and tube nut to it and had a hydraulic shop that does...
  10. 8

    88 gasser gauges in an 83 diesel?

    double check the wiring, when i swapped 87 to 88+ to get the electric speedo, a few wires needed to be switched around. Easy to trace the wires from the printed circuit.
  11. 8

    DIY shackle flip

    https://www.generalspringkc.com/shackles-hanger-kits/gm-truck-van/1967-2011/leaf-spring-hangers/ maybe get a 2wd rear hanger and see if its the same offset as yours...? My 1987 2wd I wanted a 2" drop and after researching pictures, suburbans have a factory "drop" style hanger. Holes needed to...
  12. 8

    "Sagging Motor Mounts"

    put the trans in and then the motor wont tilt back..
  13. 8

    Cruise Control wire

    it will fit, may need to take steering wheel and lock plate off but easy as the tools are cheap
  14. 8

    LS Fuel Pressure

    100%, if you plug the vent up, you ultimately will starve the engine of fuel even if the tank has fuel.... it can also deform the fuel tank if the vacuum is strong enough. Buddy built a chevelle ls swap and the vacuum deformed his tank.
  15. 8

    LS Fuel Pressure

    Humm.. I had a slightly larger aftermarket intake tube and factory mass airflow and that made mybswap run rich. I wound up putting a wideband on it and tuning the airflow sensor table.
  16. 8

    Bulkhead wiring ..HELP ..1976 K10

    Find a wiring diagram, that away you will know for sure what you have is right or wrong
  17. 8

    LS Fuel Pressure

    Just reading last posts... is your: Tune stock Intake tube stock Mass airflow sensor stock
  18. 8

    Power Door Lock Issue (and fix)

    terrible advice on the solution part ... I would recommend against using the power lock actuator to free the seized component! The door lock actuator is not designed to overcome seized components, which increases current which can burn up both switch and actuator... and then your left wondering...
  19. 8

    R10 Fan

    smh.... if you put the wrong fan blade its probably not going to work even though it will bolt up.
  20. 8

    R10 Fan

    fan blade ? or fan clutch? 14077928 is a fan blade from a scanned pdf document, but is for pre 87, maybe call dealer or venture out to a pick and pull salvage yard 87 has the reverse rotation water pump? 15734247 shows for a 87-88 454.... catalog doesn't show 87-88 with 5.0 or 5.7... best...
  21. 8

    LS Fuel Pump

    stock tbi system pressure is like 14 psi? that sounds like that would be a restriction. If you woud be using an internal pump, mine as well get one to do the whole job? stock pump for stock builds work just fine for the stock sending unit wiring. I ran just that for about 10 years on my 87 with...
  22. 8

    LS Fuel Pump

    I designed these fuel hats for the c-10 for higher current rated fuel pumps. the stock sending unit terminals can only handle 14 amps... more higher powered pumps draw more. while uncle eddy never has a problem. data sheets led me down this path this setup allows up to 25 amps on fuel pump power...
  23. 8

    Can your granny open your trucks door?

    I've never cleaned or done anything with the door push button, works just fine... what if you changed the linkage that goes from: button to lock actuator to a spring and switch. switch turns on relay that makes a 2nd door lock actuator that connects to the actual lock actuator that now opens...
  24. 8

    Delay Wiper Module

    video showing the module using the factory aka non detent switch C-10 switch demo
  25. 8

    Speedometer inaccurate and bounces

    unless new cables come non greased, original poster stated he replaced his cable...

Latest posts

Forum statistics

Threads
44,160
Posts
950,628
Members
36,273
Latest member
dannyphx
Top