Search results

  1. HEG77k10

    TIGHT door hinge

    Ok I’ll try that! Actually found some aerokroil the other day so I’ll use it.
  2. HEG77k10

    What have you done to your square lately??

    Just put a new cb in my truck, Cobra 29Ltd NW classic. Wired a marine led light strip under the dash to the courtesy light wiring, it doesn’t look so bright in person but works great.
  3. HEG77k10

    TIGHT door hinge

    The passenger door hinge on my k10 is getting really tight. I’ve lubed it up several times but it seems like those rollers mounted to the door are too tight against the metal bar that acts like a spring. Is there some way to adjust them? I’ve thought about just taking that spring out so they...
  4. HEG77k10

    Front driveshaft clunk

    Well I took out the spacers and went to jack up the crossmember so it was tight to the frame and my dumb self didn’t think abt hitting the exhaust. I just had a new exhaust put in and they did it around the transmission and transfer case WITH the drop kit installed. Transfer case doesn’t fit...
  5. HEG77k10

    Front driveshaft clunk

    All the joints are good in the cv, I didn’t even think abt the drop kit making the front angle worse. I will try taking out the spacers and seeing what it does, thanks! Do you know if there are aftermarket front drivelines that are made to go the steeper angle? I haven’t seen any that outright...
  6. HEG77k10

    Front driveshaft clunk

    Howdy! My k10 has a 6” rc all spring lift with a transmission crossmember drop kit. When in 4hi or 4lo and under power, the constant velocity double u joint binds up and jerks the whole truck with each turn of the driveshaft. It happens going straight and with the wheels turned. On the highway...
  7. HEG77k10

    Carburetor recommendation

    On my engine (400 stroker) I have a Edelbrock avs2 650. It’s basicallly the same as the performer series. Super easy to tune, easier than a Holley. Not saying they’re better but for a daily driver high hp engine I really like the Edelbrocks.
  8. HEG77k10

    What gears do I need?

    What kind of locker do you recommend?
  9. HEG77k10

    What gears do I need?

    Is that going 70miles an hour in third gear or?
  10. HEG77k10

    What gears do I need?

    So is there a thick gear set for Dana 44s? Or would I need a whole new carrier if I wanted to go down to a 4:10 from a 2:73
  11. HEG77k10

    What gears do I need?

    Has anyone used rigid axle? My dad bought his truck with 4:56 gears and it’s awfully wound up going down the freeway
  12. HEG77k10

    What gears do I need?

    Ok thanks!
  13. HEG77k10

    What gears do I need?

    So would I have to get the “thick” gears if it has 2:73s stock? I was looking at rigid axle, they have some cheaper ones.
  14. HEG77k10

    What gears do I need?

    I’m 16 so I can only afford one vehicle and it’s my daily driver right now, rebuilt th350 tranny and a 400sbc.
  15. HEG77k10

    What gears do I need?

    If anyone has a specific brand too that they like let me know, cheaper the better!
  16. HEG77k10

    What gears do I need?

    I have a 1977 k10 with factory axles. 12 bolt rear end and Dana 44 front. I wanna re gear it to 4:10/4:11 but I’m not sure what gears I need. It has stock 2:73 gears which is a little tall for 35 inch tires lol. Thx for the help!
  17. HEG77k10

    Canopy for 77k10

    Does anybody happen to know where to get a canopy that will fit a 77 k10? I’m looking for one like the blue truck has in the picture. Thanks! Green rig is mine.
  18. HEG77k10

    Bluieprint 383 stroker ISSUES Bad idle.

    I just took an 850 double pumper (message me if anyone wants to buy it) off my 400 stroker and swapped it for an Edelbrock avs2 650, I thought it was gonna be to small but it made a huge difference in how smooth it ran. Perfect for a daily driver
  19. HEG77k10

    Bluieprint 383 stroker ISSUES Bad idle.

    I’d be willing to bet your carb is the issue for fouling the plugs. What kind of carb are you running? And do you have fuel pressure regulator?
  20. HEG77k10

    Th350-400 swap

    I’ve got a rebuilt th400 and np208c t-case that I want to swap with the stock th350 and t-case in my 77 k10. Has anyone on here had any experience with that? Thanks in advance!
  21. HEG77k10

    Roll bar for sale?

    Howdy y’all, does anyone have a chrome roll bar for sale that will fit in a long bed 77 k10? I’m in sw Washington. Thanks!
  22. HEG77k10

    New sbc 400 blueprint engine keeps fouling plugs with gas

    Here’s kinda the situation now. I got a autometer afr gauge with an o2 sensor. At an idle right now it’s around 10.7-11.3. Roughly. When I’m driving and just barely touch the throttle it leans wayyy out and stumbles like crazy, gets up to 17 on the gauge. At WOT it runs perfect with no stumble...
  23. HEG77k10

    New sbc 400 blueprint engine keeps fouling plugs with gas

    There ya go bud. Thanks for the helpful Insight. :)
  24. HEG77k10

    PNW Square Buddy

    Howdy howdy from adna wa
  25. HEG77k10

    New sbc 400 blueprint engine keeps fouling plugs with gas

    Exactly

Latest posts

Forum statistics

Threads
44,401
Posts
956,724
Members
36,714
Latest member
MartinK5
Top