Search results
-
Oxygen sensor
Take it down to a muffler shop, have them drop a new hole and wells on a new Bung. 50 bucks max!- Raybo135
- Post #21
- Forum: TBI & EFI Conversions
-
How to tell if my NP203 has been converted to part time?
That is not an extra support, that is a factory option skid plate to protect the T-case while off roading and rock climbing. It comes with a protective plate under the gas tank also. It was about a $125 option from the factory.- Raybo135
- Post #26
- Forum: Transmission & Transfer Case
-
Picked up my first classic truck
Not sure if Murphy has stations in Commie California, but the Murphy stations in Colorado have 87Octane non-ethanol fuel. In California, because you are at sea level, the Octane would be 89. Also you do not need to run Mobil Premium in this motor. The compression is not high enough to warrant 93...- Raybo135
- Post #35
- Forum: Introduction
-
Picked up my first classic truck
On the 1973 350, the fuel filter was mounted on the Carburetor where the fuel line from the pump enters the Carb.- Raybo135
- Post #34
- Forum: Introduction
-
Picked up my first classic truck
73's did not come with HEI distributors. Did not come around until 1975.- Raybo135
- Post #33
- Forum: Introduction
-
oops ! Can you spot what’s wrong here?
I was going to say your low beams are on the bottom and they should be on the top. -
Power brake filter? Can’t find one
There's no fluid in your booster, so moisture should not be a problem. -
Electrical MYSTERY? Blower motor runs when key is off
They are only about 10 bucks. Splurge and it'll probably fix your problem. Or your fan switch needs to be replaced.- Raybo135
- Post #11
- Forum: Electrical & Audio
-
LMC Door / Interior Panels
What was the other place and how dressed were they? -
78 GMC seat belt styles
My original 1976 I bought in 1975 only had a lab belt, and it was a K-10 Custom Deluxe with 6200GVW. But it did have the bolt holes for a shoulder belt to bolt into the pillar. In 1976, the GVW 6200 was considered Heavy Duty. However, I have a newer 1976 now and it does have the same GVW rating... -
Seals for rear sliding window
Any ideas on jerry rigging something to stop the leaks?- Raybo135
- Post #3
- Forum: Glass & Mirrors
-
Seals for rear sliding window
Does anyone know if there is a replacement for the seals for the sliders. When I wash the truck at a brushless, water comes flowing in. The felt/rubber is all dry rotted.- Raybo135
- Thread
- Replies: 2
- Forum: Glass & Mirrors
-
Rear Window Sliding Glass
Does anyone know if there is a replacement for the seals for the sliders. When I wash the truck at a brushless, water comes flowing in. The felt/rubber is all dry rotted. -
Rear Window Sliding Glass
Hi, Aurora Girl! Where did we leave this? Last i remember you asked how to get the passenger glass out. I said there are 2 Phillips screws that hold the frame on the left side of the glass, one at the top and one at the bottom. Remove those and the frame will cone out and you'll be able to... -
Rear window clarification
What year truck is this an original for. Mine looks different. Do you have the rough measurements?- Raybo135
- Post #41
- Forum: Tech Discussion
-
Rear window clarification
Aurora Girl--I would very much like to have the Passenger side. The other guy's window is different than that from a '76 factory slider. PM me and we can discuss payment and shipping- Raybo135
- Post #40
- Forum: Tech Discussion
-
-
-
Rear window clarification
I need the piece behind the driver. I have an old original slider from my first 76 I bought in Jan 1976. The one on my new '76 must have had a camper top on it and scratched the hell out of it. Please PM me and I will buy it off you and Venmo you cash to ship it to me. Thank you, thank you...- Raybo135
- Post #20
- Forum: Tech Discussion
-
How quick is your Square?
He said he ran 15.90 at an altitude of 3500 feet. Not the distance he ran! ! !- Raybo135
- Post #53
- Forum: Engine & Performance
-
How quick is your Square?
That ain't high altitude! you shouldn't even have to adjust the jets for that. That is almost at sea level:):33::Big Laugh:- Raybo135
- Post #51
- Forum: Engine & Performance
-
How quick is your Square?
I see the gas gauge move faster than the Speedo! ! !- Raybo135
- Post #50
- Forum: Engine & Performance
-
Blower works on high only
It is on my 1976. But I think I figured out what the problem was. The Resistor that is below the Relay had a loose connection. Now my fan works on High and all other speeds. The Additional tab is for the Max Air position to run the fan on High and no other speed. I am going to put in the new... -
Blower works on high only
OK. I took the switch out and it had 5 tabs. The plug took up 4 tabs and an orange wire took up the last tab. I bought a Genuine GM and it came with only 4 tabs for the plug. What do I do with the other orange wire now? And does anybody know where can I find one with 5 tabs. -
Blower works on high only
Where is this Resistor located on a 73-78 K10? I have never seen this before and I have been around a 76 K10 since 1976. My switch just never went out before. But now it has and I needs the full speed for the A/C. Thanks for any assistance you can provide! ! !
