Search results

  1. theblindchicken

    Need help identifying t-case and tranny

    Funny you should mention that.... Mine got taken off a while back for who knows what reason.... Should probably stick mine back on there too. Wonder if it was a slight design change to help prevent leaking at the seal there since it appears that the largest difference is the addition of...
  2. theblindchicken

    CA Fuel pump nozzles and old squarebodies

    If you come up with a good solution, I'd love to know about it.
  3. theblindchicken

    Tailgate protector options?

    Could probably throw on any kind of plate that you'd like. Could even reuse the existing bolts.
  4. theblindchicken

    Need help identifying t-case and tranny

    Huh... wonder why the tailhousing on his 203 looks completely different from mine? You'd think they'd be the same.
  5. theblindchicken

    Sway Bar

    Yeah, gonna eventually replace all the balljoints and bushings. Still need to actually measure the swaybar diameter to get the right bushing for it too... Was pretty tight before the lift, my guess is something was starting to want to be replaced and the lift + big tires just made it wanna get...
  6. theblindchicken

    What have you done to your square lately??

    Long beds are usually cheaper and easier to find. Plus, when ya hook hard enough the added length will help keep the front plated to the ground.
  7. theblindchicken

    Bvllsh!t on craigslist.

    Only a shame you cant find them in 16's or 17's. Would love to have a set and have a nice selection of tires for em.
  8. theblindchicken

    1-ton swap

    Super pricey, and you still need rotors, calipers, and all the other goodies. Isn't that only a little bit higher than the cost of 8 lug swapping a 6 lug d44?
  9. theblindchicken

    Sway Bar

    I would assume a sway bar is a sway bar is a sway bar. I've got the factory sway bar on my truck using the factory mounts to the top spring plates for the front. It's gonna need a correction links for it though since it's too short to even begin to reach the spring plates with out one. The...
  10. theblindchicken

    Need help identifying t-case and tranny

    You don't have the same rounded rear output on the transfer case that I do. So I'd say its safe to say that you don't have an NP203.
  11. theblindchicken

    1-ton swap

    https://www.sneveysoffroad.com/gm_14_bolt_ff_6_lug_conversion_kit/4_wheel_parts_off_road_parts It's a full disk conversion for it, but instead of the typical 8 lug conversion, it's to 6 lug.
  12. theblindchicken

    What have you done to your square lately??

    So..... wanna come paint my truck? :rofl: Looks amazing :cheers:
  13. theblindchicken

    Bvllsh!t on craigslist.

    Oh how I would love to go buy this set up if I didn't have to save some money for a bit... 8 lug 16.5x9.5 Slot Mag $250 w/ tires https://bakersfield.craigslist.org/wto/6127958720.html
  14. theblindchicken

    1-ton swap

    I've just got a 3/4t 14bff waiting to go in.... haven't made the decision whether to convert to the 14bff to 6 lug, or convert the d44 to 8 lug. Sure do love my slot mags, but they're nearly impossible to find in a set of 8 lugs.
  15. theblindchicken

    Sway Bar

    I've got the ORD sway bar correction on my truck: 4-5" suspension & 35's as well. My truck has a tendency to follow all the grooves in the road due to the more aggressive tread of the tires. But i'll admit that I do have a fair amount of play in the steering (10-15 degrees in both directions of...
  16. theblindchicken

    CA Fuel pump nozzles and old squarebodies

    I have the same issue on my 74. I push the nozzle all the way in, then tilt the handle up. Fill it up quickly for abut 90% of what's needed, then the last gallon or so pump it slowly by hand. But yeah, haven't found a way to just flip the hold and let it do its thing yet.
  17. theblindchicken

    Rockers and floors

    Yeah, keep the amps low, then adjust the wire speed. You want to hear that sizzling bacon. For the wire speed, too low will make it burn through. Too fast and you'll notice the wire is pushing the tip away from the material. You want it to be consistently arcing. Keep the tip right about...
  18. theblindchicken

    New member from California

    Welcome to the board! An EFI conversion has piqued my interest of late, can't wait to see how yours all turns out!
  19. theblindchicken

    77 911 - Getting it going again

    I'll have to check on that one. Seems like they're pretty prone to cracking along the seam between plastic plates.
  20. theblindchicken

    77 911 - Getting it going again

    Hasn't started. School finals are here, focusing on that. Been more looking to plan out exactly what needs to be torn into first and foremost, then chug along through with that. This one will be a ton slower than my truck's progression hahah.
  21. theblindchicken

    Expedition Type Bed Rack/Rails

    For the stake mounts, I was gonna run rectangle tubing (I think the holes are 1x2"), stick weld a nut to the end of the plate and then close it up. Use a bolt and tighten it up through the bottom of the stakehole. The rears could use the same style, just but with using a horizontal bolt since...
  22. theblindchicken

    Expedition Type Bed Rack/Rails

    I've been contemplating doing a tube rack for a canvas top similar to a soft top. I bed you could do something pretty similar and utilize tabs on the tubes to mount the panels to it. Something similar to that, minus the actual basket on top. Mounts along the bed rails utilizing the stake...
  23. theblindchicken

    Not new, looking for somebody

    crazy4offroad, we're lookin for our fair share too! :crazy: Don't you worry though, soon enough you'll be back to the trucks. Just keep on rolling.
  24. theblindchicken

    Bvllsh!t on craigslist.

    Makes ya wonder what the gearing is.... 3.08's?
  25. theblindchicken

    Bvllsh!t on craigslist.

    86 Burban 30" lift on 49's...... $20k https://losangeles.craigslist.org/sfv/cto/6083265586.html

Latest posts

Forum statistics

Threads
45,466
Posts
983,995
Members
38,517
Latest member
bglendon
Top