Search results

  1. Truck82

    Really tight front brakes!

    Hey guys, I need some help with my front brakes. This week I pulled the rotors to replace/grease and replace the bearings and races. The brake pads are supper tight going back on. I can even notice it when I'm driving... like really notice it. what did/didn't I do? Has anyone had this issue? Do...
  2. Truck82

    What new tools have you got lately?

    Got this little tool today. Don’t have much to say about it accept that it works!
  3. Truck82

    What new tools have you got lately?

    Same here
  4. Truck82

    Coil spring lift spacer questions

    Thanks I really appreciate the help!
  5. Truck82

    What have you done to your square lately??

    Can you move that leaver to activate the trailer brakes independently on the truck brakes? I have an old school one on my Camper Special
  6. Truck82

    What have you done to your square lately??

    Can anyone give me any insight on how the trailer brake controller works? This sounds stupid, I know.
  7. Truck82

    Coil spring lift spacer questions

    2 inches is it then. Thanks for all the help! Hopefully it turns out. Maybe I’ll do a thread on the build.
  8. Truck82

    Coil spring lift spacer questions

    I decided to do a little experimenting tonight. I got the jack out and placed it under the front support. Then came the tape measure and I lifted it up 2 inches. Am I thinking right or will the coil spacers work differently? With 2 inches of lift there is no major (visible) alignment issue. I’m...
  9. Truck82

    What have you done to your square lately??

    I love that truck!!!! Looks awesome!
  10. Truck82

    What have you done to your square lately??

    Replaced the fuel filters. Nothin fancy. Found a spare door key behind the dash. My grandpa said it’s been there for 25+ years!
  11. Truck82

    Coil spring lift spacer questions

    I would like to respectfully say that I Hate body lifts :33:
  12. Truck82

    Sbc 350 vacuum hose help

    I always liked the GMCs over the Chevys. That’s a nice truck
  13. Truck82

    Sbc 350 vacuum hose help

    Just curious, is your truck a 1/2 ton or 3/4?
  14. Truck82

    Sbc 350 vacuum hose help

    Original hydroboost brakes. No vacuum needed. I’ve never seen any traditional booster on a diesel either. Mines leaking a little and I should probably rebuild/replace it soon.
  15. Truck82

    Sbc 350 vacuum hose help

    I wish they were all that simple :disgust:
  16. Truck82

    Coil spring lift spacer questions

    Thanks for the information! I need someone to sound like my dad with stuff like this. There’s so much information out there where some say it’s “the right way” and others will disagree. I’m on the fence now with so much input and opinions. Thanks again
  17. Truck82

    Coil spring lift spacer questions

    Do it right? Like drop spindles from an obs? I was going to go that route but money is tight. I’ve seen a lot of nice 2wd lifted with coil spacers and thought that was a good option
  18. Truck82

    Sbc 350 vacuum hose help

    Unfortunately I can’t help here. My cruise control doesn’t work so I just pulled all the lines going to it to clean things up a bit. I’m assuming your talking about the two lines your holding in your picture?
  19. Truck82

    Sbc 350 vacuum hose help

    Yup, that’s exactly what I did. My swap was a 6.2 diesel to a 350. Very similar to your swap
  20. Truck82

    Sbc 350 vacuum hose help

    When you say the small trans line I’m assuming you mean the line coming from the transmission modulator. Correct me if I’m wrong. Then yes, it goes to the port on the back of the intake. Where does the other line come from?
  21. Truck82

    Sbc 350 vacuum hose help

    Are those vacuum line going to the cruise control right now?
  22. Truck82

    Coil spring lift spacer questions

    Do you have pictures of your truck?
  23. Truck82

    Coil spring lift spacer questions

    Does the aluminum not crush under the weight? Obviously it must not be a problem but seems like it would flatten out a little. As for the lift, 2.5 - 3 inches is what I’m going for! Thanks!
  24. Truck82

    Coil spring lift spacer questions

    Howdy! First, I would like to explain my truck and its future purpose. I have a 1982 c20 that has springs from when it was a 6.2 diesel and now has a 350. This makes it leveled. I plan on doing some off road (gravel mountain roads, dirt trails, and a little snow driving with chains) and I will...
  25. Truck82

    Need help identifying this metal line coming out the back of my carburetor

    That’s what I needed to hear. Thank you :D Just wanted to know, can any vacuum port be capped off? Assuming it isn’t needed on the vehicle.

Latest posts

Forum statistics

Threads
45,456
Posts
983,873
Members
38,506
Latest member
Jimc21NC
Top