Search results

  1. W

    Where can I buy the warning light lens like fasten seat belt choke lens and 4x4 lights lens

  2. W

    Where can I buy the warning light lens like fasten seat belt choke lens and 4x4 lights lens

  3. W

    Where can I buy the warning light lens like fasten seat belt choke lens and 4x4 lights lens

    Looking for stores to buy the lens that has the warning letter on them for the clusters and what are the correct ones that goes into a 1983 cluster I know there is a low coolant one as well is that one on a 83?
  4. W

    Oil pressure sender switch and coolant sender what type of thread sealant to use since your not supposed to use Teflon so it can ground correctly

    Oil pressure sender switch and coolant sender what type of thread sealant to use since your not supposed to use Teflon so it can ground correctly
  5. W

    Oil gauge issue

    Since we can’t use Teflon what do we use to seal it?
  6. W

    New tach conversion kit from usa1 how to mount the tach to the mounting bracket

    There are nuts on the tach that looks like you would take off and use to mount the tech to the holding bracket but they said thoses nuts are what hold the electrical board down so they said you would use your old nuts to mount the tech to the holding bracket and leave thoses new nuts alone on...
  7. W

    1983

    What are the len lights supposed to say in the cluster like choke/fasten seat belts brake 4wd and there placement?
  8. W

    New tach conversion kit from usa1 how to mount the tach to the mounting bracket

    I seen post awhile ago I think from a lmc conversion kit saying you need to use your old nuts to hold the rack to the mounting bracket because if you use the nuts on back of the tach to mount to bracket it will not work can anyone confirm getting ready to put all this back together? Thanks
  9. W

    ‘83 K5/ SBC 350 Swap/ new/old oil sending unit differences/dash gauge/Autometer gauge?

    Where can people buy the 45 fitting from
  10. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

    Check out new boyz squarebody rescue I was able to get in contact with them and they had each complete wire I needed. All I got to do now is put them in super great customer service as well
  11. W

    454 swap k10 what fittings are needed to install oil pressure sender and switch

    Do you guys have the part numbers or know where the best place would be to buy new sensors and units
  12. W

    454 swap k10 what fittings are needed to install oil pressure sender and switch

    Wondering where to mount senders and switch and what fitting I need to mount to block
  13. W

    Used a drill to check speedometer forgot I had drill on two and the speedometer spun all the way around

    used drill to check speedometer drill was in 2 speed and it jumped my needle all the way around I put drill back on 1 and seems to be working right running around 25 on drill is everything going to be okay and work properly or will I have to order new speedometer
  14. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

    Update found them they was all cut very close to the bulkhead they was hard to see can I take it apart and add new wires from inside out of the connector or will I have to just connect the short pieces
  15. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

    When the tan pink/white and dr blue comes out of bulk head should they run across where wall toward motor or will they run to radiation and around that way
  16. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

    Dis gram shows this as brk pressure wring switch what do I need to order so it plugs in correctly
  17. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

  18. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

    That’s what I was think it deff has the white stripe but coudnt tell the color and the diagrams I have seen can’t tell if it’s in the right pin location for it but that does explain why I can’t find it so I could could connect and run it over to new pressure switch
  19. W

    Wiring for oil pressure switch sending unit and coolant wiring help

    There’s also this wire coming out of bulk head that’s cut can you tell what it is and what it’s supposed to go to?
  20. W

    Wiring for oil pressure switch sending unit and coolant wiring help

  21. W

    Wiring for oil pressure switch sending unit and coolant wiring help

  22. W

    Wiring for oil pressure switch sending unit and coolant wiring help

    1983 I understand just relaying to locate the wires to see what I have to order so I can get all my garages working correctly again since the swap previous owner did
  23. W

    Little wire cut from bulk head what did it go to? Looks to have white stripe with it but can’t tell other color?

  24. W

    Wiring for oil pressure switch sending unit and coolant wiring help

    I brought a truck with 454 swap I’m looking to buy new sending units and pressure switches for coolant and oil and hook everything back up factory so the cluster works I’m having hard time finding the wires I’m need to hook everything back up factory I have looked at the wiring harness pages and...
  25. W

    What Sending units oil and water temp needed for guage cluster to work like factory in k10 454 swap I will buying all the components new thank you

    dd190 did you also do a 454 swap?

Latest posts

Forum statistics

Threads
45,043
Posts
974,153
Members
37,968
Latest member
randomlostguy
Top