Search results

  1. Dmack

    Looking for a decent bench seat cover that doesn't break the bank...

    It is held on with several straps with plastic buckles on them, and woven laces on the sides to cinch them tight. Probably the only seat covers I have ever used that don't come loose, ever. Fairly easy to remove.
  2. Dmack

    Looking for a decent bench seat cover that doesn't break the bank...

    https://www.basspro.com/shop/en/cabelas-trailgear-low-back-seat-covers?hvarAID=shopping_googleproductextensions&ds_e=GOOGLE&ds_c=BPS%7CShopping%7CPMax%7CProprietary%7CGeneral%7CNAud%7CNVol%7CNMT&gclid=CjwKCAjwjMiiBhA4EiwAZe6jQ8OboRDFYtJmqgqyRc6w8AGRmYLLzsPF18Yt9EyoXlO-2WpecbpS2RoCYCIQAvD_BwE&gcls...
  3. Dmack

    69 C10

    Nice
  4. Dmack

    69 C10

    Nice. What are your plans for It? Just pulled parts off a 70 and trashed the rest. Saying it was rough is an understatement.
  5. Dmack

    New Air Compressor

    I picked up a couple of Husky 7hp 60gal an CL several years ago for $200ea. One for the shop and one for the garage. Much quieter and more useful than the oilless Craftsman I had for years.
  6. Dmack

    Need some Expertize for paint job

    Guess it depends. When I did my K20, I did the interior and complete exterior, minus the inside of the bed (raptor liner ). It took one gallon of color and one gallon of clear. When doing 2 stage, you thin the paint 2-1, so you get 2 gallons of sprayable product.
  7. Dmack

    6" lift what wheel and tire size can I fit? I want 35's but don't know how wide of a tire and rim i can fit.

    I have the same 315/75R16 on my 83 K20 with a 4" Rough Country lift. I believe they are considered a 34" tall tire. No rubbing. It's my dd and I'm not an avid off-roader, so i dont know what hapoens when you flex it out.
  8. Dmack

    Adhesive remover

    Any reason you don't want to use the eraser wheel? I used one on the old trim adhesive on a bed I painted and it worked fine.
  9. Dmack

    69 C10

    Nice progress. I haven't made much progress on my 70 for the last year. It actually had 2x4s for rockers. Lots of patch panels, which I luckily got before all the supplies dried up. Keep up the good work.
  10. Dmack

    Truck left me stranded today.

    Don't forget the filter in the inlet of the carb.
  11. Dmack

    Favorite Project Truck Sales Pitches

    Drove 4 hours to look at a 69 C10. Was told "engine runs strong". As I drove up, I could see the starter hanging just off the ground by the main wire. Popped the hood and the heads and intake were missing. I said "runs strong"? He says "well, it will once you put it together".
  12. Dmack

    Compressor overload keeps tripping

    Make sure you are getting 110v to both legs, not just one.
  13. Dmack

    Help with fuel guage problems

    The general rule is if it reads below empty (9 oclock) the unit is grounded out. If it reads last full (3 oclock), it is an open circuit.
  14. Dmack

    700R4 Spews fluid when in reverse.

    Necropost
  15. Dmack

    Oil pressure question… or two questions

    You are assuming the factory gauge and sender areaccurate. After changing the sender in mine twice, I put a mechanical gauge in it. Gm crate engine with unknown miles and maintenance. 40 on cold startup and 30 warm.
  16. Dmack

    Fuel gauge repair HELP

    Sounds like it. That shows the gauge is working, and tells me the wiring is good. I have had several bad sending units with open circuits over the years.
  17. Dmack

    Fuel gauge repair HELP

    Past full means you have an open circuit. Usually means a bad connection, broken wire, or bad sending unit. Needle past empty is grounded.
  18. Dmack

    DIY Raptor Bed-liner

    I used on mine about 3 years ago. Overall, I'm happy with it. Looks good, but longevity isn't anywhere near the commercial jobs. The raptor will scrape off if I drag a piece of metal with any sharp edge. I also slide 25gal propane tanks over the tailgate and it will wear through.
  19. Dmack

    Mounting tires at home

    Thanks for the link. Looks like a decent design other then the flimsy bar. May have to do some experimenting. My current project is a 1970 C20 I have swapped an 84 C10's running gear into. I have some used BFG 31's in going to mount on the ralleys.
  20. Dmack

    Radiator removal

    You will need to pull the fan first. Once out, I pull the staples and replace them with two 5\16" x1" bolts so you can easily pull the top separately in the future. Comes in handy when working on the belts, changing ps pump, water pump, etc. And welcome.
  21. Dmack

    Mounting tires at home

    If you get a chance, I would like to see a pic of a bar that actually works. Thanks
  22. Dmack

    CA legal LS swap

    Nice write up. Makes for one more reason I'm glad I don't live there .
  23. Dmack

    Bed liner yes or no

    I have a 99 Dodge Cummins, a 50 Ford F1, my 83 Square, and my newest project, a 1970 Chevy C20. I don't discriminate by brand.
  24. Dmack

    Bed liner yes or no

    I used it in my 83. Looks good, very grippy, but not nearly as heavy or rugged as the commercial spray in types. Of course, it only cost me $50, as opposed to $400+ for a commercial job. I have a rubber mat in my Dodge, and that would still be my first choice.
  25. Dmack

    Going price for 8' beds

    I just parted out an 84 to use in my 70. Box was rough and couldn't get a call at $75. Ended up pulling it apart to keep the near perfect floor. Cut a filler door for TheFishBox 's project, and scrapped the rest. Finally got $50 for a good cab and frame.

Latest posts

Forum statistics

Threads
44,614
Posts
962,577
Members
37,155
Latest member
Troyport
Top