Search results
-
-
-
Tips on cutting holes in ABS dash
Yes, welcome. You've got a black slate there...... Endless opportunities...guy on my K5 forum just make the sickest dash I've ever seen: -
Painted interior trim.....with bedliner:
Use a good quality brush and lay it on. A roller will pick it up as it goes over it, thus pulling it up and leaving a much more textured surface....more like you would want in your bed...not n yor dash. However, dont expect to use it again afterwards, this stuff wont clean off. Thats why... -
Painted interior trim.....with bedliner:
A condensed version will be added to my build thread: http://www.gmsquarebody.com/forum/showthread.php?t=5266 ,but I thought I would expound upon it with its own. My trim situation was that I had a dash cover over the oe, my A-pillars and head liner trim were gray...including the pieces the... -
Bvllsh!t on craigslist.
http://phoenix.craigslist.org/evl/pts/3658052645.html- 8T6K5
- Post #10,827
- Forum: eBay & Craiglist Listings
-
New guy from Ohio
Welcome. You need to get a build thread going and provide a plethora of pics....ASAP!- 8T6K5
- Post #2
- Forum: Introduction
-
Cab roof lights...
Keeping this thread alive. Working on the 'Burban dual switch install. Once I get the housing installed, the top switch will remain the window switch. Plan for the bottom is to run my cab lights off it. Thw switch is ON-OFF-ON....I want to keep it like that. Once I figure out which... -
Heat/AC Distribution Troubleshooting/Vacuum Control
Perfect...I think, Ill look closer...want to prewire it for cab lights. -
Heat/AC Distribution Troubleshooting/Vacuum Control
Whenever, no rush. Would like to know the wire sources for the rear ac on-off-on switch, power in and gorund? -
Heat/AC Distribution Troubleshooting/Vacuum Control
Quick interuption, 89s do you have the rest of that manual scanned? I wouldnt mind seeing pg178, have Q about switch for rear air.... -
Foot switch....
No axle swap anytime soon. Need to drive and enjoy this for awhile... Stereo if anything next Got to have a booming system when I cruise the mall for high school chicks... Sent from my iPhone using my iPhone- 8T6K5
- Post #22
- Forum: Electrical & Audio
-
Foot switch....
- 8T6K5
- Post #20
- Forum: Electrical & Audio
-
Foot switch....
Done... Yellow wie to 12v Green to 86 Bown not needed..... Lights on - lights off...just like bights. Just rigged to see if I was wasting my time. Will clit up and mount tomorow... :)- 8T6K5
- Post #18
- Forum: Electrical & Audio
-
Foot switch....
True. I just want to run 1 set of lights... the 2 Hello 550's inside the grill. I am still very geen with wiring, ut from what Ive seen, here's how would wire it... [/IMG] Basically with the foot switch, I will take the yellow wire to the fuse box. Now Im unsure what I should do...- 8T6K5
- Post #17
- Forum: Electrical & Audio
-
-
-
Foot switch....
Might just pull right off the new dist block and use a relay just so theres a ground...?? Sould be a fun mess...- 8T6K5
- Post #5
- Forum: Electrical & Audio
-
Foot switch....
Soooo.... I would use green for lights and yellow for 12v power in? Tan?- 8T6K5
- Post #3
- Forum: Electrical & Audio
-
is there a 4 headlight mod for our trucks?
http://www.gmsquarebody.com/forum/showthread.php?t=5966&highlight=beams -
Foot switch....
Picked up an old foot switch... I want to re-wire some aux lights to it. Switch has 3 wires coming from it, A - B - C on the switch. Im guessing one is power in - power out and ground...??- 8T6K5
- Thread
- Replies: 21
- Forum: Electrical & Audio
-
is there a 4 headlight mod for our trucks?
Search. We just covered this. Sent from my iPhone using my iPhone -
Bvllsh!t on craigslist.
Do WANT...!! http://portland.craigslist.org/mlt/cto/3650215995.html- 8T6K5
- Post #10,796
- Forum: eBay & Craiglist Listings
-
What have you done to your square lately??
F'ing truck wouldnt start this AM... WTF now right? No fuel pressure...damn I hope it aint the pump...having that gauge just paid for itself :) Just the relay :) -
Did the Blazers come with rear side panels?
gotta be something in your settings...?
