Search results
-
steering column lower trim piece
No need to return. Just pay it forward if some one else needs it. Am good on the shipping too -
-
Time for this beast to get a CB Radio LOL
Will that impact your income or expense?- Red Rex
- Post #20
- Forum: Tech Discussion
-
-
1984 GMC K1500 4x4 short bed avatar truck
Yeah and I can’t blame my boys now when I can’t find a tool -
steering column lower trim piece
Pm address. I do not do PayPal I will just do to the post office and mail it. If more than 7.5 I will message you otherwise just mail me a check. I will not be able to get to it until next Monday or Tuesday -
1984 GMC K1500 4x4 short bed avatar truck
My grandsons are 10 and 8. I am by far not the original owner but have been the owner for the last. 14 I think years -
steering column lower trim piece
I have one NCtyphoonkid sent me a other the radio I bought from him. You can have it for postage from 30354 -
1984 GMC K1500 4x4 short bed avatar truck
Thanks. I am pretty attached to this truck and both my grandsons want it. Really I am getting cold feet (prob something you know well in Pa.) about selling -
1984 GMC K1500 4x4 short bed avatar truck
High Sierra trim. PS,PB,PW,PL, cruise, tilt. 350 4 bolt main one piece rear seal stock except Wieand intake and MSD pro billet distributor and 6A box. New process 208 case, TH350 transmission, 10 bolt limited slip with 3.08 gears. Xtra tail gate, nib 6a digital box, many other misc parts... -
-
Can this be welded?
Pricing is 200 plus from summit I am looking for torque so would a set of long tube headers be a cheaper option ?- Red Rex
- Post #6
- Forum: Tech Discussion
-
-
-
8 MPG?
Just do I understand what you are saying, the distance from the top of the piston to the mating surface of the head when installed should be .040 to .045? If correct what compression ratio would that produce withs 64 cc heads?- Red Rex
- Post #95
- Forum: Tech Discussion
-
Any bikers?
Had one of those. Fantastic bike. Sold it to get cash for the closing on the first house I bought. Always Been a Brit owner, even a 1980 BSA thunderbolt and a couple Triumph doubles- Red Rex
- Post #47
- Forum: Other Vehicles
-
Hard to refuse freebies
Ford ruined what was a good car when the bought Volvo- Red Rex
- Post #31
- Forum: Other Vehicles
-
Can this be welded?
It is a cast iron pipe plug held in with job weld thanks to one of my boys. The manifold is split on the bottom under where it fits in. Rock auto has them for (ouch) $166 each plus shipping when in stock. Cannot find one at a junk yard, seems these were only on the vin m engines I will pull...- Red Rex
- Post #3
- Forum: Tech Discussion
-
Can this be welded?
Is this repairable? If not does anyone have a driver’s side they would part with? Factory steel tube exhaust manifold- Red Rex
- Thread
- Replies: 6
- Forum: Tech Discussion
-
Choke not closing on rebuilt quadrajet
I ran a wire from the choke housing screw to the battery ground post. Once you get the linkage right be sure the carb is grounded good or the choke plate will take excessive time to open, creating a rich mixture issue- Red Rex
- Post #21
- Forum: Carb Fuel Systems
-
8 MPG?
84 GMC 4wd short bed 350 quadrajet on weiand intake 3.08 gears Th350 transmission MSD pro billet dizzy w6a box 30 inch tires 10 mpg @55- Red Rex
- Post #54
- Forum: Tech Discussion
-
-
Mounding issue
Appreciate the replies. I will have to look for those activator pads. Been 90 days of 00+ degree heat here in Atlanta and I think that may have been a factor- Red Rex
- Post #4
- Forum: Paint and Body
-
Mounding issue
The 2 sided tape on my body mouldings is letting go. It is 1 yr old. Is there a better way to stick mouldings on? Best quality tape? Glue? Appreciate suggestions- Red Rex
- Thread
- Replies: 3
- Forum: Paint and Body
-
Leaf spring builders??? anyone know of any?
Eaton Detroit spring. I have a set of 7 leaf on my truck. Highly recommend. Call them and have a conversation- Red Rex
- Post #6
- Forum: Suspension, Steering & Brakes
