Search results

  1. G

    Pic of the clutch rod on a 4 speed where it goes through the floor, I replaced my floors and need to drill the hole for the clutch rod. Much appreciat

    Got it thanks all
  2. G

    For the life of me I Can't get this tailgate off, Any Tricks?

    I don't think I could have done this truck without all the valuable information from the folks here. I'm struggling with getting my tailgate off so i can remove the bed. It's a 73 K 20 any Ideas Thanks in advance.
  3. G

    Need help boys what is this?

    Thank you for the reply I figured that out, but was brain dead for a few lol.
  4. G

    Need help boys what is this?

    So doing my full restore floors rockers everything in got a few issues, but starting putting the dash back and can’t figure out where this plugs in I have the full wiring diagram don’t see it.
  5. G

    Anyone dealt with LMC Trucks for parts?

    it's a scam100% for sure as someone who ran a tech company take my word for it. Advice for anyone on our site if you are ordering from anyone online always check the browser line for the address it has to contain the https:/www to be a secure site if you notice all these phishing sites start...
  6. G

    How much paint do I need, and other questions

    do this before anything, go to autobody 101 forums and read all you can they are the best resource for someone who has never attempted a paint job, It's way more complex than you think. It's doable just take your time. Oh and it will cost more than you think.
  7. G

    Pic of the clutch rod on a 4 speed where it goes through the floor, I replaced my floors and need to drill the hole for the clutch rod. Much appreciat

    Thank you so much CalSgt that's exactly what I was looking for.
  8. G

    Pic of the clutch rod on a 4 speed where it goes through the floor, I replaced my floors and need to drill the hole for the clutch rod. Much appreciat

    Pic of the clutch rod on a 4 speed where it goes through the floor, I replaced my floors and need to drill the hole for the clutch rod. Much appreciated
  9. G

    Removed my entire heater system?

    Than you Guy's I got the hose you pictured
  10. G

    Removed my entire heater system?

    My entire system is ripped out, I saw somewhere on the site a replacement part like a u shaped hose to bypass the core hose connections. Anyone know what that was? I just need to temporarily put it in till i install a restomod air and heat system, which means a hold till i find 2k for that lol...
  11. G

    New Here from N.E. California

    Welcome from the Bay Area
  12. G

    Silly question about my leaf springs on my 73k20

    Your opinions are well taken since it’s stock I’ll keep it that way for sure. Maybe I should raise it
  13. G

    Silly question about my leaf springs on my 73k20

    interesting so that is stock, so what do I need to lower it?
  14. G

    Silly question about my leaf springs on my 73k20

    Did the factory build trucks with springs on top of the axel? I would doubt it but my truck seems lifted both the front springs and rear are on top of the axles. How hard would it be for me to put them back to factory? Here is how far it’s disassembled, we’ll at least the front
  15. G

    Confusion on Torque spec

    Did all the above thanks
  16. G

    Confusion on Torque spec

    I've got the rear correct for sure, it was the front nut i was wondering about and why my service manual say 50ft-lbs for the front nut
  17. G

    Confusion on Torque spec

    right tight and back off for the rear, but the front nut?
  18. G

    Confusion on Torque spec

    I'm confused, replaced my front wheel bearings on my 73 k 20 did the back bearing to spec ends up at about 35 ft-lbs with the backing off, however the consensus on this forum is the fronts should be torqued to about 120 ft-lbs, I have the factor serv manual and the factory overhaul manual and...
  19. G

    Lowering

    what color is that truck
  20. G

    Instrument cluster upgrade 1974 C10

    no you got the right one that’s what I was pointing you towards
  21. G

    Engine Misfire/Shutoff after just 30 minutes of driving

    Drake did anyone ever answer your question
  22. G

    1975 c20 backfire issues

    what carb is on it? Could have blown out the accelerator pump, I think it’s firing order related, with gas that old it’s crap full of varnish, you need a clean gas source
  23. G

    Instrument cluster upgrade 1974 C10

    John if you’re using a factory cluster with the printed circuit on the back there are two versions of that one for a tach and one for no tach. Lic list both the replacement cost is about 60 dollars, I have a 73 myself without tach but am going to get the tach version. Where your file gauge is is...
  24. G

    Weird wheel question?

    thanks guys I may have measured wrong so 6.5 it is And yes the center hole is right at 5 inches
  25. G

    Weird wheel question?

    My 73k20 has 16.5 x 6.5 inch white steel rims, 8lug I measured the bolt pattern center to center and I get 6 inches, and the center hole is 5” why can’t I find any rims for it, seems everything is 6.5 bolt pattern?

Latest posts

Forum statistics

Threads
44,168
Posts
950,776
Members
36,283
Latest member
Cantrell299
Top