Search results
-
F
What have you done to your square lately??
It’s the shops, not mine. I’m just about the only one that uses it. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Made part of the 5” tailpipe tonight Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Capped the sides of the flatbed but I need to figure out where I want to put the filler necks. I think I’m putting them In at an angle recessed into the side/top of the bed in a pocket. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Picked up the steel I had cut for my flatbed project to make sides for it. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Installed my new marker lights I need to order the correct hardware for them and tint them soon. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Reinstalled the seatbelts, did an oil change, topped off the fluids. Installed the bumper that was originally on the truck and cleaned it up with some steel wool. Need to bend a few things back on the bumper so it doesn’t look as bad.this was before cleaning it up. Sent from my iPhone using... -
F
What have you done to your square lately??
Installed the lock strip in the rear window seal today, fixed my high beams, tried to fix my wipers but some how managed to make them always stay on when I didn’t touch any wiring, I’m guessing faulty switch, secured my coolant reservoir and the washer fluid tank in place. Sent from my iPhone... -
F
Pulse or intermittent wipers?
I knew about the cruise and no cruise being different, I also found the earlier trucks have a different length stick than the later ones. My truck had cruise but it was eliminated when the PO swapped the 6.5 into it. I’m hoping I can grab a matching switch and stalk. Sent from my iPhone using...- fmxr47
- Post #4
- Forum: Electrical & Audio
-
F
Pulse or intermittent wipers?
Hello all, I’m having trouble with my wiper switch and the turn signal stalk and just want to replace them both. How do I know which wiper system I have? I have a tilt column and I can choose from puke or intermittent. TIA Sent from my iPhone using Tapatalk- fmxr47
- Thread
- Replies: 3
- Forum: Electrical & Audio
-
F
What have you done to your square lately??
Repaired some grounds for my lights, cleaned up the interior some, and finally drove it home for the first time since I started this project. High beams are not working at the moment though. sitting in the drive. Sent from my iPhone using Tapatalk -
F
3/4 ton? Wheels?
Yes I am running these although without wheel spacers the front tie rods ends ever so slightly rub the wheels. I’m going to run 2” spacers most likely and that should get them back to a stock looking stance. Sent from my iPhone using Tapatalk- fmxr47
- Post #5
- Forum: Wheels and Tires
-
F
What have you done to your square lately??
Started working on the wiring inside the cab, wired up a radio also. I may need an antenna extension wire. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Bolted my bed on today Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Test fit my flat bed and started some measuring and trimming of the rear of the bed. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Started the reconstruction of my flatbed. Trying to keep it low to an extent. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
I started reworking my flat bed I got in a trade a few years ago I narrowed it down to 80”, cut off the headboard to remake, cut off the stake pockets on the rear as well. Now to clean up the edges and determine what material I want to cap the sides with. I may be angling the back of the bed... -
F
What have you done to your square lately??
Yes you are correct, they are inboard brakes since it is full float. I am just trying to get everything turning without having to pull the axle shafts yet, and then pull the hubs off with a bearing pulling. I was hoping someone had a trick to get everything moving before going through all that... -
F
What have you done to your square lately??
Fought With this free 14 bolt FF I got from my dad. It sat outside at our farm for probably 20 years or more [emoji51]. Can’t get anything to spin, surprisingly the oil inside wasn’t discussion except for some rusty sediment from moisture over time. Diff will rock back and forth but the drums... -
F
What have you done to your square lately??
Installed my shackle flip brackets today Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Removed a bunch of unnecessary junk from the frame this evening and burned a hole in my frame [emoji51] something else to weld up [emoji1743][emoji3603][emoji1751][emoji3603] Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Reinstalled the transmission most of the way after doing a starter, rear main seal, and flexplate along with attempting to wash and degrease the trans and transfer case while it was out. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Began prepping for transmission removal so I swap flex plates and rear main seal. Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
I have a bad habit of tackling far too many projects at once! Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Bought the flex plate and rear main seal I’ve been dragging my feet on getting, now to see if I actually install them soon Sent from my iPhone using Tapatalk
