Search results

  1. cbrown5385

    RPM sticking sometimes.

    I’m also not sure if this is part of the issue but at first start up this thing SCREAMS! Then if I tap the throttle it’ll bump it down to the high idle and then if I hit it again it’ll bump down to normal idle
  2. cbrown5385

    RPM sticking sometimes.

    I’m going to have to watch the linkage and the choke I thought I had the choke adjusted well, but the stuck linkage or cable would make a lot of sense
  3. cbrown5385

    RPM sticking sometimes.

    I’m having a slight problem I have 86 k10 with a carbureted 350. Every so often when just crushing and pulling up to and intersection the ideal wants to remain high to where I almost have to rev it a little bit to get the ideal back down to its resting spot. I did it today coming into my drive...
  4. cbrown5385

    Fuel cell to stock gauge

    Hey guys is it possible to wire a fuel cells level sender into the stock gauge?
  5. cbrown5385

    So I’m having an issue with fuel pump

    So I’m having fuel supply issue. I’m thinking I have a plugged fuel supply line. I have an electronic fuel pump mounted on the frame. It was running fine then slowly started supplying less and less fuel until finally supplying none. I swapped out pumps and still same issue….. im Think...
  6. cbrown5385

    Does any one know what had a similar banjo as this?

    Any idea what year and model that exact fitting would have come on?
  7. cbrown5385

    Does any one know what had a similar banjo as this?

    Does any one know what had a similar banjo as this? Very hard to locate. It came off an 85 c10 but I can’t find the replacement
  8. cbrown5385

    Dropping regulator pressure

    I out an ACES efi kit on an86 k10 with a small block 350
  9. cbrown5385

    Dropping regulator pressure

    Guys I’m having an issue. I turn my keys on which powers my electric fuel pump the fuel pressure on my regulator goes right up to 47 where it’s set up when the pump is done cycling pressure at the regulator goes back to zero and I get a no start. Any thoughts? I’ve pulled both fuel filters and...
  10. cbrown5385

    What’s the solution to this?? Idle adjustor

    Sorry for the late response I’m trying to lower the idle on start up, I’ve replaced IAC but it is still a bit high.
  11. cbrown5385

    What’s the solution to this?? Idle adjustor

    So I went to adjust my idle on my 90 suburban and found the adjuster like this!
  12. cbrown5385

    Fuel pressure issue

    I am having an issue with my fuel pressure regulator, I did an ACEs efi swap with an inline fuel pump. I cannot get the regulator pressure to move and it is stuck at 80 psi on the gauge, when I shut the truck off it’ll drop down to zero. No amount of turning the adjuster bolt in or out will...
  13. cbrown5385

    Is there a good spot for keyed power under the hood?

    I’m wiring the ACE’s efi kit. It supplies a super small 18 guage wire that I’m thinking powers a relay in the system with the wiring being that small and there being larger 12 gauge wire. This is a whole kit with fuses and relays already in line. Sorry I wasn’t even thinking of putting that in...
  14. cbrown5385

    Is there a good spot for keyed power under the hood?

    Good afternoon everyone. Is there’s a decent spot for keyed power under the hood, instead of running back into the cab fuse block?
  15. cbrown5385

    Suburban lowering.

    Has Anyone split the spring pack instead of doing a flip kit?
  16. cbrown5385

    Edelbrock 660 electric choke

    Would it not being hooked cause an issue when starting after it’s already been driven I feel like I am constantly to stomping on the throttle while cranking it to get it running.
  17. cbrown5385

    Edelbrock 660 electric choke

    Sorry I meant to add this with that.
  18. cbrown5385

    Edelbrock 660 electric choke

    Can anyone explain how the electric choke works on the Edelbrock 660 in regards to starting after the trucks already been running and driven. Mine is not wired in and restarting the truck tends to be a pain in the ass. Also is there a way to test it to make sure it’s actually working before or...
  19. cbrown5385

    Seat recovering

    Think I’ve finally got it done minus one bolt in the seat track mount to the floor and the frigan red seat belts that the bolts won’t even budge on!
  20. cbrown5385

    Seat recovering

  21. cbrown5385

    This is a pretty cool build.

  22. cbrown5385

    This is a pretty cool build.

    My buddy has a pretty cool build going on I don’t think he’s on here but he’s Trav.Builds on you tube.
  23. cbrown5385

    Suburban rear quarter panel

    Has anyone found anyone selling this patch panel?
  24. cbrown5385

    Seat recovering

    Seat bottom! Hoping to have carpet and seats fully installed by the weekend but ran into a water in the cab issue! But I didn’t want to risk putting the carpet and seats in with the water leak!
  25. cbrown5385

    I’m guessing seam sealer isn’t going to stop the water from coming in….

    Pulled the cowl and seam sealed everything up top and still water leaking in… looked further and found this…

Latest posts

Forum statistics

Threads
44,168
Posts
950,766
Members
36,283
Latest member
Cantrell299
Top