Search results
-
Picked up a 1982 C30 yesterday... adding to the list of projects!
Welcome from Kansas Cool truck.- Terry Wilkerson
- Post #6
- Forum: Introduction
-
-
Fuseable link
I used a 14 guage fuseable link to power the high speed on the blower motor. Is this the right way or should have I used an inline fuse?- Terry Wilkerson
- Thread
- Replies: 3
- Forum: Electrical & Audio
-
Fuse block connectors
Added constant power for Dakota digital, radio constant, and fule pump relay. All low power. Oh and dome light. Dome light was not hooked up who knows why.- Terry Wilkerson
- Post #5
- Forum: Gauge, Speedo & Instrumentation
-
Fuse block connectors
I'm lookin for fuse block connectors for added circuits. Anyone have a number or source for the correct ones. My truck is a 1986 gmc.- Terry Wilkerson
- Thread
- Replies: 5
- Forum: Gauge, Speedo & Instrumentation
-
Fuel tank brackets
I used a board and 2 clamps to force the strap into the bolt hole to start the nut. As said before do this on the ground before installing. Good luck it will fit.- Terry Wilkerson
- Post #4
- Forum: Carb Fuel Systems
-
First time square owner from TN
Welcome from Kansas Like those original bed rails.- Terry Wilkerson
- Post #8
- Forum: Introduction
-
-
-
-
-
For you LS swap guys.
Got the motor and trans in. Drove it a few miles. It idles fast randomly. Got any ideas? Looked for vac leaks could not find any?- Terry Wilkerson
- Post #40
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
-
Brake switch removal
On my 86 gmc I need to replace the brake lite switch. It look like I need to drop the steering wheel to get this done. Am I missing something?- Terry Wilkerson
- Thread
- Replies: 1
- Forum: Gauge, Speedo & Instrumentation
-
Lowering truck
Anyone running 275 60 R15 on ralley's on the front with 2 1/2 drop spindles from lmc?- Terry Wilkerson
- Post #9
- Forum: Lowered & Street Systems
-
Lowering truck
Yes it's an Ls swap and yes a new driveshaft will be made. I've been thinking about a mild drop. I've been told by my nephew we should do the drop before making the driveshaft. He probably right. This build has snowballed like crazy. They all do.- Terry Wilkerson
- Post #7
- Forum: Lowered & Street Systems
-
Lowering truck
When lowering the rear end of a square will the drive shaft need to be shortened?- Terry Wilkerson
- Thread
- Replies: 11
- Forum: Lowered & Street Systems
-
Radiator condenser combo.
Seems as no one has an aluminum radiator in stock for my 86 gmc. Was planning on using an original configuration because the ac condenser lines come around the end of the rad on the right side into the engine bay. This limits me on the length of a rad. Question is if I use a later modle wider...- Terry Wilkerson
- Thread
- Replies: 21
- Forum: Engine & Performance
-
-
Fuse block question.
The dome light isn't supposed to come on on door open??- Terry Wilkerson
- Post #3
- Forum: Gauge, Speedo & Instrumentation
-
Fuse block question.
Is it ok to use a male crimp on spade for a connection here? My dome light needs plugged in and the end is gone. Hot wired it and it works just isn't plugged in.- Terry Wilkerson
- Thread
- Replies: 4
- Forum: Gauge, Speedo & Instrumentation
-
-
What is this?
Thanks guys. It comes out tomorrow.- Terry Wilkerson
- Post #7
- Forum: Gauge, Speedo & Instrumentation
-
What is this?
My truck is a 1986 gmc 1500 rwd. Doing a ls swap on it. What is this? It's underside of passenger dash.- Terry Wilkerson
- Thread
- Replies: 8
- Forum: Gauge, Speedo & Instrumentation
-
Engine lift points
It's out. I remover the core support. It will make it easier to install the 6.0 and trans in one piece. Thanks for all the comments.- Terry Wilkerson
- Post #13
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
